527-149NCP1A1B3C1 datasheet, PDF

Datasheet> All Categories > 527-149NCP1A1B3C1

Preview

527-149NCP1A1B3C1: DescriptionStrain Relief Backshell; File Size59KB，2 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet View All

527-149NCP1A1B3C1 Overview

Strain Relief Backshell

Preview

Download Datasheet

View All

527-149

Strain Relief Backshell

for Size 2 ARINC 600 Series Connector

ARINC 600

Backshells

527-149 NF P A3 B4 C5

Basic Part No.

Finish (Table II)

Connector Designator (Table III)

Position and Dash No. (Table I)

Omit Unwanted Positions

1.50

(38.1)

Thread Size

(MIL-C-38999

Interface)

Position

1.79

(45.5)

Position

5.61 (142.5)

.50 (12.7) Ref.

Cable

Range

Position A

View A-A

Metric dimensions (mm) are indicated in parentheses.

CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

E-Mail: sales@glenair.com

F-10

Recommended Resources

Commonly used non-sinusoidal oscillator circuits, waveforms and frequency calculation formulas-square wave oscillator-self-excited multivibrator

555 TV grid generator circuit

10w low frequency integrated amplifier circuit

Ultra shortwave tuner circuit with M0S prestage

Common base transformer feedback oscillation circuit

Six-way infrared remote control power switch

LM46002AQ: Has anyone used this power chip (LM46002AQPWPR)? The design is to output 12V (input wide voltage 3.9-24V). Now it is measured that no matter how much the input is, the output is about 4V, and the FB p...; xxhhzz Power technology

[Ask TI] Common high-frequency boards have many vias between the upper and lower ground planes. Can you tell me what the benefits are?: [i=s] This post was last edited by dontium on 2015-1-23 13:34 [/i] My initial idea is to eliminate the inductive reactance between the upper and lower layers and some decoupling effect. I don’t know i...; 梦之旅 Analogue and Mixed Signal

I want to integrate some discrete components in the circuit. Which companies in China can do this?: [b]I want to integrate some discrete components in the circuit. Are there any domestic companies that can do this? [/b]...; city379 Analog electronics

Can I use chipscope to see the waveform if I only have one spatarn-6 board?: I only have a Spatarn 6 board, and I want to use chipscope to observe the waveform of a Verilog counter. Now I set up the project in ISE, and set up the net in the scope inserter, but when I click sta...; boruili FPGA/CPLD

Help OPA561 op amp is getting hot: This is the circuit I built using multisim:The actual build is the same as above. Because OPA561 is not in multisim, the OPA561 model is built by myself, and the pins are a bit strange, sorry. Pin 4 o...; yushengjiexy Analog electronics

[TI millimeter wave radar evaluation]_1_AWR1843BOOST unboxing: [i=s]This post was last edited by lbbook on 2019-12-9 23:23[/i]Thanks to TI and EEworld team for organizing the mmWave development board evaluation event. I am very lucky to be qualified to evaluate A...; lbbook TI Technology Forum

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components