EEWORLDEEWORLDEEWORLD

Part Number

Search

10XS3412_09

Description
Quad High Side Switch (Dual 10 mOhm, Dual 12 mOhm)
File Size1MB,53 Pages
ManufacturerFREESCALE (NXP)
Download Datasheet Compare View All

10XS3412_09 Overview

Quad High Side Switch (Dual 10 mOhm, Dual 12 mOhm)

Freescale Semiconductor
Advance Information
Document Number: MC10XS3412
Rev. 10.0, 10/2009
Quad High Side Switch
(Dual 10 mOhm, Dual 12 mOhm)
The 10XS3412 is one in a family of devices designed for low-voltage
automotive lighting applications. Its four low R
DS(ON)
MOSFETs (dual
10 mOhm/dual 12 mOhm) can control four separate 55 W / 28 W
bulbs, and/or Xenon modules, and/or LEDs.
Programming, control and diagnostics are accomplished using a
16-bit SPI interface. Its output with selectable slew rate improves
electromagnetic compatibility (EMC) behavior. Additionally, each
output has its own parallel input or SPI control for pulse-width
modulation (PWM) control if desired. The 10XS3412 allows the user to
program via the SPI the fault current trip levels and duration of
acceptable lamp inrush. The device has fail-safe mode to provide fail-
safe functionality of the outputs in case of MCU damaged.
Features
• Four protected 10 mΩ and 12 mΩ high side switches (at 25°C)
• Operating voltage range of 6.0 V to 20 V with sleep current
< 5.0
μA,
extended mode from 4.0 V to 28 V
• 8.0 MHz 16-bit 3.3 V and 5.0 V SPI control and status reporting
with daisy chain capability
• PWM module using external clock or calibratable internal
oscillator with programmable outputs delay management
• Smart over-current shutdown, severe short-circuit, over-
temperature protections with time limited autoretry, and fail-safe
mode in case of MCU damage
• Output OFF or ON open-load detection compliant to bulbs or
LEDs and short to battery detection. Analog current feedback
with selectable ratio and board temperature feedback.
• Pb-free packaging designated by suffix code DPNA
V
DD
V
DD
V
PWR
V
DD
V
PWR
10XS3412
HIGH SIDE SWITCH
PNA SUFFIX (PB-FREE)
98ARL10596D
24-PIN PQFN
ORDERING INFORMATION
Device
MC10XS3412CPNA
MC10XS3412DPNA
Temperature
Range (T
A
)
- 40°C to 125°C
Package
24 PQFN
10XS3412
VDD
I/O
SCLK
CS
SI
I/O
SO
MCU
I/O
I/O
I/O
I/O
A/D
GND
WAKE
FS
SCLK
CS
SO
RST
SI
IN0
IN1
IN2
IN3
CSNS
FSI
GND
VPWR
HS0
LOAD
HS1
LOAD
HS2
LOAD
HS3
LOAD
Figure 1. 10XS3412 Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2008. All rights reserved.

10XS3412_09 Related Products

10XS3412_09 10XS3412
Description Quad High Side Switch (Dual 10 mOhm, Dual 12 mOhm) Quad High Side Switch (Dual 10 mOhm, Dual 12 mOhm)
PPC 2002 source code ported to EVC4 standard SDK, Aygshell.h encountered problems
I want to port a PPC 2002 source program to the EVC4 standard SDK so that it can run on a normal wince system. I used EVC4 to open the project file, and failed to compile it in the standard SDK enviro...
jxzg101 Embedded System
[Flower carving hands-on] Interesting and fun music visualization series of small projects (23) - 3 in 1 flash point optical fiber
I suddenly had the urge to do a series of topics on music visualization. This topic is a bit difficult and covers a wide range of areas. The related FFT and FHT algorithms are also quite complicated, ...
eagler8 DIY/Open Source Hardware
How to write a C51 program for a 51 single-chip microcomputer using a crystal oscillator as a timer?
How to write a C51 program for a 51 single-chip microcomputer using a crystal oscillator as a timer?...
dreamwalk Embedded System
A brief introduction to active crystal oscillators and passive crystal oscillators
Passive crystal oscillator Passive crystal oscillator is crystal. Passive crystal oscillator is a non-polar component with 2 pins. It needs the help of clock circuit to generate oscillation signal. It...
安圣基 PCB Design
Focus handling issues in soft keyboard implementation
I am making a soft keyboard, and now it is basically finished, but the focus of the soft keyboard cannot be controlled. My software disk is a CDialog, which sends messages to CEDIT and other objects. ...
hhyyzzcool Embedded System
I would like to ask about the PB customization system under VS2005.
> I am new to Wince. I have installed VS2005 and its SP1, and Wince6.0. The PB plug-in also appears in VS2005. After customizing it according to some examples on the Internet, the following prompt app...
moseshuilan Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 221  2066  2783  2240  1809  5  42  57  46  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号