1N4001 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Discrete semiconductor> diode> 1N4001

1N4001: Description1 A, SILICON, SIGNAL DIODE; CategoryDiscrete semiconductor diode; File Size55KB，2 Pages; ManufacturerJinan Jing Heng Electronics; Websitehttp://www.jinghenggroup.com/

Download Datasheet Parametric Compare View All

1N4001 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	1N4001	-	-	View	Buy Now

1N4001 Overview

1 A, SILICON, SIGNAL DIODE

1N4001 Parametric

Parameter Name	Attribute value
Maker	Jinan Jing Heng Electronics
Reach Compliance Code	unknow
Shell connection	ISOLATED
Configuration	SINGLE
Diode component materials	SILICON
Diode type	RECTIFIER DIODE
JEDEC-95 code	DO-41
JESD-30 code	O-PALF-W2
Number of components	1
Number of terminals	2
Maximum operating temperature	150 °C
Minimum operating temperature	-65 °C
Maximum output current	1 A
Package body material	PLASTIC/EPOXY
Package shape	ROUND
Package form	LONG FORM
Maximum repetitive peak reverse voltage	50 V
surface mount	NO
Terminal form	WIRE
Terminal location	AXIAL

Preview

Download Datasheet

View All

1N4001 Related Products

	1N4001	1N4003	1N4005	1N4002	1N4007	1N4004	1N4006
Description	1 A, SILICON, SIGNAL DIODE	1 A, SILICON, SIGNAL DIODE, DO-41	1 A, 600 V, SILICON, SIGNAL DIODE, DO-41	1 A, 100 V, SILICON, SIGNAL DIODE, DO-41	1 A, 1000 V, SILICON, SIGNAL DIODE, DO-41	1 A, 400 V, SILICON, SIGNAL DIODE, DO-41	1 A, 800 V, SILICON, SIGNAL DIODE, DO-41
Maker	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics	Jinan Jing Heng Electronics
Reach Compliance Code	unknow	unknow	unknow	unknow	unknow	unknow	unknow
Shell connection	ISOLATED	ISOLATED	-	ISOLATED	ISOLATED	ISOLATED	-
Configuration	SINGLE	SINGLE	-	SINGLE	SINGLE	SINGLE	-
Diode component materials	SILICON	SILICON	-	SILICON	SILICON	SILICON	-
Diode type	RECTIFIER DIODE	RECTIFIER DIODE	-	RECTIFIER DIODE	RECTIFIER DIODE	RECTIFIER DIODE	-
JEDEC-95 code	DO-41	DO-41	-	DO-41	DO-41	DO-41	-
JESD-30 code	O-PALF-W2	O-PALF-W2	-	O-PALF-W2	O-PALF-W2	O-PALF-W2	-
Number of components	1	1	-	1	1	1	-
Number of terminals	2	2	-	2	2	2	-
Maximum operating temperature	150 °C	150 °C	-	150 °C	150 °C	150 °C	-
Minimum operating temperature	-65 °C	-65 °C	-	-65 °C	-65 °C	-65 °C	-
Maximum output current	1 A	1 A	-	1 A	1 A	1 A	-
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	-	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	-
Package shape	ROUND	ROUND	-	ROUND	ROUND	ROUND	-
Package form	LONG FORM	LONG FORM	-	LONG FORM	LONG FORM	LONG FORM	-
Maximum repetitive peak reverse voltage	50 V	200 V	-	100 V	1000 V	400 V	-
surface mount	NO	NO	-	NO	NO	NO	-
Terminal form	WIRE	WIRE	-	WIRE	WIRE	WIRE	-
Terminal location	AXIAL	AXIAL	-	AXIAL	AXIAL	AXIAL	-

Recommended Resources

Digital/analog (A/D) converter output interface circuit diagram composed of uA741

555 power-on delay output low level circuit

Low Cost Integrated Circuit Power Amplifier 02

C534J1 vertical lathe main circuit

Two-stage inverter with protection diode

Inclination sensor thermal wire circuit diagram c

LIS3DH chip problem consultation: [table=98%] [tr][td][color=#444444]Hello everyone, I found a problem when I was doing LIS3DH motion detection. [/color][color=#444444]After configuring the registers of LIS3DH (configuring the motion ...; lskam stm32/stm8

The MCU cannot run in DC-DC mode of BLUENRG-1: In the DC-DC mode of BLUENRG, the voltage output is only about 0.5V, and the output of LDO is also only about 0.5V. The MCU cannot operate normally, and the SWD interface cannot be detected using J-li...; suwithin ST - Low Power RF

My emergency light is fully completed. See the picture.: All the components I used are from MAXIM. Although the workmanship is not very particular, you can take a look at them for reference. The pictures were supposed to be uploaded tomorrow, but because my...; ddllxxrr DIY/Open Source Hardware

Repost: Data format conversion example of sending SMS using Siemens TC35 series GSM module: ...; fish001 RF/Wirelessly

How to debug nandflash?? (as the title says software debugging): Anyone who has done this before, please give me some tips. Thanks....; yangjunweimail Embedded System

Pull-up and pull-down resistors: Sometimes the unused pins of a chip cannot be left floating, and a pull-up resistor or a pull-down resistor is needed to make it at a high or low level. Why not connect it directly to the power supply...; zhonghuadianzie Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components