OP260 datasheet, PDF - EEWORLD Datasheet

OP260: DescriptionDUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER; File Size762KB，16 Pages; ManufacturerADI; Websitehttps://www.analog.com

Download Datasheet Compare View All

OP260 Overview

DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER

	OP260	OP-260FZ	OP-260FJ	OP-260AZ	OP-260AJ	OP-260ARC/883	OP-260
Description	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER	DUAL, HIGH-SPEED, CURRENT FEEDBACK, OPERATIONAL AMPLIFIER

I just bought lm4f120, and when I adjust the PWM wave, I always run into a strange place.: The development environment is keil realview mdk, the source code is attached. There are two main problems: 1. When configuring GPIO, use the GPIOPinConfigure function, but GPIO_PXX_M0PWM0 is not foun...; 火书 Microcontroller MCU

I have a circuit design question: Why does the signal have to pass through the NAND gate before reaching the destination (AND with the high level, equivalent to no change); is there any harm in passing it directly?...; yangxf1217 PCB Design

Does STM32 need CPU participation to write SPIflah?: Does STM32 need CPU to be involved continuously when writing SPI flash? I mean, can the CPU do other work when writing SPI FLASH, such as ADC.In fact, this is the main summary of my other question." A...; eddie7434 stm32/stm8

The mouse cursor is not displayed when there is no mouse in the XPE C# software: The program running under xpe needs to realize the function of no mouse and no keyboard. It runs normally when the mouse is plugged in. After unplugging the mouse, the mouse cursor on the screen disap...; zhushuping Embedded System

The boiler pressure feed water pump is controlled by variable frequency PID, and the pressure always runs at or below the given pressure?: 1. The equipment is a constant pressure PID control system for the water supply pump in the hot water heating boiler room; 2. During debugging, it was found that the system pressure was controlled at ...; eeleader-mcu Industrial Control Electronics

Differences between software simulation and reality: void main(void) { int t; Init_CLK(); uint ch[8] = {0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80}; Init_Port(); t=KeyScan(); P5DIR=0XFF; P5OUT=ch[t]; while(1); } After using while, the output of P5 is corre...; wangfei890912 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components