EEWORLDEEWORLDEEWORLD

Part Number

Search

54112-412301950LF

Description
Board Connector, 30 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size67KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54112-412301950LF Overview

Board Connector, 30 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54112-412301950LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.768 inch
body length1.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54112
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts30
Base Number Matches1
PDM: Rev:G
STATUS:
Released
Printed: Feb 20, 2009
.
PCB impedance design
1. Thickness values (mil) of three commonly used prepregs under different conditions. Copper represents the TOP and BOTTOM layers, gnd represents the power supply or ground layer, and signal represent...
settleinsh FPGA/CPLD
Does anyone know how to design a low-pass elliptic filter?
[i=s] This post was last edited by paulhyde on 2014-9-15 09:11 [/i] Help, does anyone know how to design a low pass elliptic filter with a cutoff frequency of 10m (or other)? Is it better to use an ac...
qiukaixiang Electronics Design Contest
LM3S9B95 program cannot be downloaded
IAR for ARM 6.10, J-Link emulator 4.22b, LM3S9B95 C5 version chip. The hardware diagram is attached. The error message is AHBID error? I really don't understand. The emulator is fine, even a 9B96 boar...
ultrabenz Microcontroller MCU
Disassembly of small reduction motor
[align=center][b][font=宋体][size=14.0pt]Disassembly of small reduction motor[/size][/font][/b][/align][align=center]DIY&Sharing—GravityShare[/align][align=center][align=center][font=宋体][size=12.0pt][hr...
万有引力平台 DIY/Open Source Hardware
How to output Gerber files for 4-layer boards in AltiumDesigner
[i=s]This post was last edited by littleshrimp on 2016-12-19 19:14[/i] GP1 and GP2 here are negative films, do they need special settings?In the generated gerber file, I see that the middle electrical...
littleshrimp PCB Design
Why does the resolution decrease when the gain is increased?
Why does the resolution decrease when the gain is increased?...
QWE4562009 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1162  1508  956  2528  1612  24  31  20  51  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号