EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AA-01-9533-C

Description
Fixed Resistor, Thin Film, 0.25W, 953000ohm, 100V, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AA-01-9533-C Overview

Fixed Resistor, Thin Film, 0.25W, 953000ohm, 100V, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP

B0202AA-01-9533-C Parametric

Parameter NameAttribute value
MakerTT Electronics plc
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance953000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.25%
Operating Voltage100 V
Base Number Matches1
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
stm8l-discovery download and debugging issues
The debug mode cannot be started. What is going on? The JP1 jumper cap is connected to on, and both ST-LINK jumpers are also connected. The error message is as follows: Tue May 01 14:38:43 2012: Faile...
emily83_zheng stm32/stm8
【AT-START-F425 Review】 2. Development Environment Construction and Demo Examples
AT-START-F425 provides MDK Keil pack and corresponding Fireware, so development is relatively easy;After installing the pack package, you can see it in the keil option Open the official demo programFi...
kit7828 Domestic Chip Exchange
Is anyone familiar with lithium battery protection IC? If I want to verify these parameters, is there a special instrument? It shouldn't be...
Is anyone familiar with lithium battery protection IC? If you want to verify these parameters, are there special instruments? It shouldn't be verified with an oscilloscope, multimeter, or constant tem...
QWE4562009 Test/Measurement
About WINCE compilation problem
During the compiling process of wince, I only saw that many LIB files were generated, such as netui.lib, but how did it generate DLL files from these LIB files in the end? For example, netui.dll....
liplip Embedded System
Semiconductor material bottleneck
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:59[/i]The bottleneck of semiconductor supporting materials needs to be broken through 2006-7-6  The Semiconductor Equipment and Materia...
ehk Mobile and portable
Design of Isolated Word Speech Recognition System Based on DSP
Design of Isolated Word Speech Recognition System Based on DSP...
shaomingyi DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1921  2010  2235  1663  736  39  41  45  34  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号