KOA SPEER ELECTRONICS, INC.
SS-211 R5
AHA 06/28/06
Thin Film Chip Inductors
Type KL73 1206
1. Scope
This specification applies to Thin Film Chip Inductors (KL73) 2B size
produced by KOA Corporation.
CERTIFIED
CERTIFIED
2. Type Designation
The type designation shall be the following form:
New Type
KL73
Type
2B
Size
2B: 1206
T
Termination
Material
T: Sn
(Other termination
styles available,
contact factory
for options)
TE
Packaging
TE: 7" embossed plastic 4mm pitch
(2B - 4,000 pieces/reel)
4N7
Nominal
Inductance
4N7: 4.7nH
47N: 47nH
B:
C:
G:
J:
G
Tolerance
±0.1nH
±0.2nH
±2%
±5%
3. Rating
Item
Nominal Inductance Range (nH)
Inductance Tolerance
Quality Factor (typ.)
Self Resonant Frequency (typ.) (MHz)
DC Resistance (typ.) (Ω)
Allowable Current (max.) (mA)
Operating Temperature Range (°C)
Storage Temperature Range (°C)
Ratings
2.2 ~ 100 (E-12 series)
± 2%, ± 5% (± 0.2nH: Under 4.7nH)
15 ~ 40
400 ~ 9,000
0.25 ~ 2.00
250 ~ 1,000
-40°C ~ +85°C
-40°C ~ +125°C
PAGE 1 OF 7
Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without pr ior notice. Please confir m technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-211 R5
Rating Table
Part
Designation
KL732BTTE2N2*
KL732BTTE2N7*
KL732BTTE3N3*
KL732BTTE3N9*
KL732BTTE4N7*
KL732BTTE5N6*
KL732BTTE6N8*
KL732BTTE8N2*
KL732BTTE10N*
KL732BTTE12N*
KL732BTTE15N*
KL732BTTE18N*
KL732BTTE22N*
KL732BTTE27N*
KL732BTTE33N*
KL732BTTE39N*
KL732BTTE47N*
KL732BTTE56N*
KL732BTTE68N*
KL732BTTE82N*
KL732BTTE100*
Inductance
(nH)
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
12
15
18
22
27
33
39
47
56
68
82
100
Inductance
Tolerance
Quality
Factor
Minimum
Self Resonant
Frequency
Minimum
(MHz)
9000
7000
6000
5000
4500
4000
3500
3000
2500
40
G: ±2%
J: ±5%
25
2000
1.00
1500
500
DC
Resistance
Maximum
(Ω)
Allowable
DC Current
Maximum
(mA)
1000
Measured
Frequency
(MHz)
25
C: ±0.2nH
0.25
900
900
0.50
800
500
35
1000
2.00
400
200
500
15
400
200
* Add tolerance character (B, C, G, J)
4. Dimensions and Construction
c
L
c
Marking
Protective
Coating
Inner
Electrode
t
d
Coil
Pattern
Ceramic
Substrate
Electrode
5. Marking
5-1 Coating and Marking Color
Coating color:
Dark blue
Direction mark color:
Yellow
5-2 Marking Method
Inductance value shall be indicated to
two letters marking of significant figures.
An alphabetical letter N shall replace
position of decimal point.
(Example of marking)
2.2
2.2nH
5.6
5.6nH
10
10nH
47
47nH
Direction
mark
W
Insulation Direction
Mark
Film
Type
(Inch Size Code)
L
Dimensions
inches
(mm)
W
c
d
.02±.008
(0.5±0.2)
.016
+.008
-.004
+0.2
)
(0.4
-0.1
t
.024±.004
(0.6±0.1)
2B
(1206)
.126±.008 .063±.008
(3.2±0.2) (1.6±0.2)
5N6
Decimal
point
PAGE 2 OF 7
Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without pr ior notice. Please confir m technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-211 R5
6. Characteristics
6-1 Test Condition
Unless otherwise specified, the standard range of atmospheric
conditions for marking measurements and tests is as follows:
Ambient temperature: 20 ± 15°C
Relative humidity:
65 ± 20%
If there may be any doubt on results, measurements shall be made within the following limits:
Ambient temperature: 20 ± 2°C
Relative humidity:
65 ± 5%
6-2 Measurement Method of L and Q
Test equipment:
Fixture:
Measuring frequency:
Hewlett Packard RF Impedance analyzer 4191A
Hewlett Packard Test fixture 16092A
500 MHz/1.0nH ~ 22nH (1.0nH ~ 15nH)
200 MHz/27nH ~ 100nH (18nH ~ 27nH)
1. Perform auto-calibration to the HP4191A .275" (7mm) unknown connector connected to
0Ω/0S/50Ω standard terminations.
2. Connected the test fixture 16092A.
Measure the open circuit admittance (Go, Bo), and the short circuit impedance (Ro, Xo).
Ro
Xo
Rx
Gm + j Bm
4191A
Caribration
plane
Go
Bo
Xx
16092A Spring clip fixture
Coil
Gm
Ro
Go
Rx
+ jBm:
+ jXo:
+ jBo:
+ jXx:
Measured admittance [S]
Residual impedance [Ω]
Stray admittance [S]
Unknown impedance [Q]
3. Set pattern up and ground side to direction mark on insulator.
Measure admittance (Gm, Bm).
Chip inductor (Face up)
Spring clip
Insulator (Teflon)
Dimensions of insulator (Teflon)
in inches (mm)
.118 (3.0)
Grand plane
Terminal
Cross section of 16092A
.039 (1.0)
.106 (2.7)
4. The L and Q value shall be given the following equation. (Compensated calculation)
G
m
- G
o
- R
o
(G
m
- G
o
)
2
+ (B
m
- B
o
)
2
B
o
- B
m
X
x
=
- X
o
(G
m
- G
o
)
2
- (B
m
- B
o
)
2
X
x
Q = X
x
L=
,
2πf
R
x
R
x
=
L: Inductance of coil
Q: Quality factor of coil
f: Measuring frequency
PAGE 3 OF 7
I
Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without pr ior notice. Please confir m technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-211 R5
6-3 Characteristics
Item
Insulation
resistance
Requirement
More than 10
4
MΩ
Test Method
DC 500V, 1 minute between
both terminals and center
of reverse side.
V
More than 10
3
MΩ
DC 500V, 1 minute
Between both terminals and center
of protection coating.
V
Dielectric
withstanding
voltage
Without distinct damage
DC 500V, 1 minute
Between both terminals and center
of protection coating.
V
Terminal
strength
∆
R/R: Within ± 1%
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
No mechanical damage by
cracks or stripping, etc.
Soldered chip on wiring board A for
test is to be bent down to .118" (3 mm)
as below drawing.
(Set condition)
Dimensions in inches (mm)
Wiring board A
for test
Chip coil
Support
(ø5)
Solder
1.77 (45.0)
Within
±2
1.77 (45.0)
PAGE 4 OF 7
Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without pr ior notice. Please confir m technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-211 R5
6-3 Characteristics (continued)
Item
Requirement
Test Method
.786 (20)
1.97 (50)
Weight
R230
.118
(3.0)
Ohmmeter
Dimensions in inches (mm)
Vibration
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
95% of the terminal should
be covered with new solder
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
∆
L/L: Within ± 2%
∆
Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
Inflict 2 hours in each direction
of X, Y, Z at vibration of 10 ~ 55Hz,
amplitude .059 (1.5)
260 ± 5°C, 10 ± 1 second
Resistance to
solder heat
Solderability
Shock
resistance
230 ± 5°C, 3 ± 0.5 second
Inflict the impulse 3 times to both
directions (total 18 times) along
perpendicular axis that test condition
100G, 6 months
-40°C ± 3°C, 1,000 ± 4 hours
Low temperature
operation
Heat resisting
property
125°C ± 2°C, 1,000 ± 4 hours
Temperature
cycling
-40 ± 3°C, 30 minutes/125 ± 2°C,
30 minutes 100 cycles
PAGE 5 OF 7
Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without pr ior notice. Please confir m technical specifications before you order and/or use.
京公网安备 11010802033920号
EEWORLD
