Available in Commercial and Industrial temperature
ranges
Available in 8-pin SOIC and TSSOP Packages
P2384A
Product Description
The P2384A is a versatile frequency multiplier that is
designed specifically as cost effective alternative to the
high precision frequency oscillator.
The P2384A can generate a 4X output clock of the input
frequency that allows system cost savings by using an
inexpensive crystal or resonator to achieve high frequency
multiplication.
The P2384A provides up to 312 MHz output clock
frequency through the use of the Phase-Lock-Loop (PLL)
technique which delivers low jitter and high precision
synthesized clocks.
Applications
The P2384A is targeted towards the high frequency CAN
OSC replacement market.
systems.
Applications include xDSL,
routers, networking, PC peripherals, and embedded
Block Diagram
PDB
FS0
LF
VDD
PLL
Modulation
XIN
XOUT
Crystal
Oscillator
Frequency divider
Phase detector
Feedback divider
CLKOUT
VCO
Output
divider
VSS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200, Campbell, CA 95008
•
Tel: 408-879-9077
•
Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
February 2007
rev 0.2
Pin Configuration
XIN
1
XOUT
2
8
P2384A
VDD
FS0
CLKOUT
VSS
P2384A
7
6
5
PDB
3
LF
4
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN
XOUT
PDB
LF
VSS
CLKOUT
FS0
VDD
Type
I
O
I
I
P
O
I
P
Description
Crystal connection or external reference frequency input
Crystal connection. If using an external reference, this pin must be left
unconnected.
Power-down control pin. Pull low to enable power-down mode. Connect directly to
VDD in normal operation and if not used.
External loop filter for the PLL. (See Loop Filter Selection Table for value.)
Ground connection. Connect to system ground.
Clock output.
Digital logic input used to select Input frequency range.
(See Input Frequency Selection.) This pin has an internal pull-up resistor.
Connect to +3.3 V.
Input Frequency Selection
FS0
0
1
Input (MHz)
20 to 38
39 to 78
Output Frequency Scaling (MHz)
80 to 152
156 to 312
Low Cost Frequency Multiplier
Notice: The information in this document is subject to change without notice.
2 of 10
February 2007
rev 0.2
Loop Filter Selection Table ( VDD 3.3 V )
Pin 4 LF
C2
R1
C1
P2384A
Input (MHz)
20
21 - 22
23 - 24
25 - 26
27 - 28
29 - 30
31 - 32
33 - 34
35 - 36
37 - 38
39 - 42
43 - 46
47 - 50
51 - 54
55 - 58
59 - 62
63 - 66
67 - 70
71 - 74
75 - 78
FS0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
C1(pF)
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
C2(pF)
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
100,000
R1 (ohms)
330
390
510
560
620
750
820
910
1,000
1,200
330
390
510
560
620
750
820
910
1,000
1,200
Low Cost Frequency Multiplier
Notice: The information in this document is subject to change without notice.
3 of 10
February 2007
rev 0.2
Output Clock Selection Example
P2384A
The P2384A can generate 4X Clock from the Input reference frequency. P2384A’s internal crystal oscillator circuits allow
the use of an inexpensive crystal or resonator to replace expensive CAN oscillators that are used in networking, PC
peripherals, xDSL, and consumer applications for high frequency generation. Its input frequency range is optimized for
operations from 20 MHz to 78 MHz, and its output frequency can deliver up to 312 MHz.
25 MHz
1 XIN
2 XOUT
3 PDB
R1
C1
4 LF
VDD 8
FS0 7
CLKOUT 6
0.1µF
+3.3V
Modulated 100 MHz
VSS 5
P2384A
C2
Low Cost Frequency Multiplier
Notice: The information in this document is subject to change without notice.
4 of 10
February 2007
rev 0.2
Absolute Maximum Ratings
Symbol
V
DD
, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD 22- A114-B)
P2384A
Parameter
Voltage on any pin with respect to Ground
Rating
-0.5 to +4.6
-65 to +125
-40 to +85
260
150
2
V
Unit
°C
°C
°C
°C
KV
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
DC Electrical Characteristics
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
(Internal input pull-up resistor on FS0 and PDB)
Input high current
(Internal input pull-up resistor on FS0 and PDB)
XOUT output low current
XOUT output high current
Output low voltage (V
DD
= 3.3 V, I
OL
= 20 mA)
Output high voltage (V
DD
= 3.3 V, I
OH
= 20 mA)
Static supply current*
Typical dynamic supply current
(25 pF scope probe loading)
Operating voltage
Power-up time
Clock output impedance
Parameter
Min
VSS - 0.3
2.0
–
–
–
–
–
2.5
–
–
3.0
–
–
Typ
–
–
180
0
10
10
–
–
3
28
3.3
7
28
Max
0.8
VDD + 0.3
–
–
–
–
0.4
–
–
–
3.6
–
–
Unit
V
V
µA
µA
mA
mA
V
V
mA
mA
V
mS
Ω
* XIN and PBD are pulled low.
Low Cost Frequency Multiplier
Notice: The information in this document is subject to change without notice.
In the emergency communication network, the network nodes that need to be interconnected in the on-site wireless network include several mobile vehicles and several independent teams of personnel. Bot...
I would like to ask you if it is possible to make a receiving program for serial port interrupt, which receives a string of data each time it enters interruption and ends when it encounters a specifie...
As shown in the simulation diagram, LM324 and IRF540N form a voltage follower. Below 10V, the output is the input voltage, but above 10V, the output can only reach 10V. I don't quite understand the pr...
[color=#333333][font="][size=14px]I have been learning Xunwei's 4412 development board for a while. Today I encountered a problem [/size][/font][/color][color=#333333][font="][size=14px]I used Xunwei'...
In the early 1990s, portable phones were all the rage. With the rapid development of electronic technology, today's mobile phones can not only send emails and text messages, but also take photos, ch...[Details]
Magnetic resonance imaging (MRI) systems can take high-resolution cross-sectional perspective images of the human body, providing very useful information for medical diagnosis. The radio frequency pro...[Details]
The circuit shown in the figure is a three-digit tachometer used to measure low frequency signals with a repetitive time interval of 0.235 to 15 seconds. The tachometer has a speed range of 4 to 255 r...[Details]
Magnetic resonance imaging (MRI) systems for medical and scientific applications require a high-performance, high-power inductor capable of establishing a uniform, strong magnetic field. Transverse el...[Details]
Introduction
The market for wireless telemetry products is developing rapidly. Recently, the industry has also set off a revolution in wireless applications. Wireless telemetry technol...[Details]
Maximize instrument utilization and reduce
test times
Increasing the throughput of automated test systems can improve efficiency. Using off-the-shelf tools (COTS) such as multicore proc...[Details]
In the test of the electronic ignition module, in order to simulate the real working condition of the electronic ignition system, the electronic ignition module is often placed in an environment hi...[Details]
Infrared remote control is widely used in household appliances, security, industrial control and people's daily life, especially household appliances and security.
When there are many TVs, VCD...[Details]
In view of the problems in the actual FPGA development process, such as difficulty in locating faults, long compilation time after repeated code modification, and inability to confirm fault solutio...[Details]
With the development of supermarket industry and the strengthening of loss prevention awareness, the use of electronic anti-theft equipment (EAS) has become very popular in various parts of the countr...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
Many MEMS devices, such as accelerometers and mechanical resonance devices, require a vacuum environment to realize their designed functions. However, verifying whether the package cavity has reach...[Details]
introduction
In engineering practice, ultrasonic waves are often used to measure distances because of their strong directivity, slow energy consumption, and long propagation distance in th...[Details]
Some application designs have higher requirements on the speed at which the system's switching power supply can provide voltage output. Figure
1
shows
the
bootstrap
...[Details]
Abstract:
This paper
introduces a data acquisition system based on USB and DSP, which takes advantage of the high-speed transmission characteristics of USB2.0. The overall structure of the ...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
