EEWORLDEEWORLDEEWORLD

Part Number

Search

51702-31105600BALF

Description
Board Connector, 67 Contact(s), 4 Row(s), Male, Straight, Solder Terminal, LEAD FREE
CategoryThe connector    The connector   
File Size239KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51702-31105600BALF Overview

Board Connector, 67 Contact(s), 4 Row(s), Male, Straight, Solder Terminal, LEAD FREE

51702-31105600BALF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionLEAD FREE
Reach Compliance Codecompliant
Other featuresTERMINAL PITCH FOR POWER CONTACTS: 6.35 MM
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL (50)
Contact completed and terminatedGOLD (5) OVER NICKEL (50)
Contact point genderMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number51702
Mixed contactsYES
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded4
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts67
UL Flammability Code94V-0
Base Number Matches1
PDM: Rev:P
STATUS:
Released
Printed: Dec 20, 2010
.
【Design Tools】ChipScope Pro User Guide ---- Attached code and test waveforms
This article introduces how to use ChipScope Prothrough a specific example , gives the whole code , and ModelSim simulation results. I have tried this example and can get the desired results, so I rec...
GONGHCU FPGA/CPLD
533MHz Processor S3C2443 Wiring Guide
The same applies to S3C2450. The BGA spacing of S3C2443 is 0.5mm, which is much higher than the 0.8mm of S3C2410 and S3C2440, and requires a much higher PCB process, and blind holes need to be made....
gina MCU
How can I give the following circuit a signal source for simulation?
The passband signal frequency obtained after filtering by the above circuit is required to be around 60KHZ. How to simulate the signal source (the software I use is multisim)? Could you please explain...
州平卞 Analog electronics
What is 5v tolerance?
Can a 5V tolerant pin be connected directly to a 5V power supply without damage? Can a non-5V tolerant pin be connected to a 5V power supply with a resistor in series (using its internal clamp protect...
kjxxbjb stm32/stm8
【TI recommended course】Recommendation #Consumer Electronics Application and Design Seminar#
//training.eeworld.com.cn/TI/show/course/5540...
lukouGao TI Technology Forum
Sampling clock design of V2.0~
Consider that the clock frequency is greater than 100MHz, and the phase should be relatively accurate. Moreover, when the sampled signal is 50M, in order to achieve an effective resolution of more tha...
FLT9006 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 761  843  104  626  1938  16  17  3  13  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号