5962-88746012X datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> The power supply circuit> 5962-88746012X

5962-88746012X: DescriptionFixed Negative Standard Regulator, 5V, CQCC20,; CategoryPower/power management The power supply circuit; File Size131KB，19 Pages; ManufacturerLinfinity Microelectronics

Download Datasheet Parametric View All

5962-88746012X Overview

Fixed Negative Standard Regulator, 5V, CQCC20,

5962-88746012X Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
Maximum input voltage	20 V
Minimum input voltage	7.5 V
JESD-30 code	S-CQCC-N20
Number of functions	1
Number of terminals	20
Working temperatureTJ-Max	150 °C
Working temperature TJ-Min	-55 °C
Maximum output current 1	0.5 A
Maximum output voltage 1	5.15 V
Minimum output voltage 1	4.85 V
Nominal output voltage 1	5 V
Package body material	CERAMIC, METAL-SEALED COFIRED
Package shape	SQUARE
Package form	CHIP CARRIER
Certification status	Not Qualified
Regulator type	FIXED NEGATIVE SINGLE OUTPUT STANDARD REGULATOR
surface mount	YES
Terminal form	NO LEAD
Terminal location	QUAD
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Changes in accordance with NOR 5962-R025-93.

Add case outline N. Techical and editorial changes throughout. Redrawn.

Changes in accordance with NOR 5962-R132-96.

Make changes to case outline N dimensions A, E, S, and S1. Redrawn. - ro

DATE (YR-MO-DA)

93-03-11

95-03-27

96-05-24

98-04-13

APPROVED

M. A. FRYE

R. MONNIN

Add radiation hardness requirements. Add CAGEs 27851, 21845 and case

outline M. Make changes to 1.2, 1.2.2, P

, theta JC, and theta JA as specified

under paragraph 1.3, table I, figure 1 and figure 2. - ro

00-01-28

R. MONNIN

Add case outlines 4 and 5. Make correction to case outline N pin descriptions.

- ro

Add footnote to case outline U, TO-257 package as specified under 1.2.3 and

figure 1. -rrp

For case outline T only, add footnote 1/ under 1.2.3 and make change to note 2

under figure 1. -rrp

02-02-11

R. MONNIN

05-02-04

R. MONNIN

06-01-23

R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

JOSEPH A. KERBY

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

CHARLES E. BESORE

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, 5 VOLT NEGATIVE

REGULATOR FIXED, MONOLITHIC SILICON

DRAWING APPROVAL DATE

89-08-28

AMSC N/A

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-88746

DSCC FORM 2233

APR 97

5962-E156-06

1.3 Absolute maximum ratings.

Input voltage:

Operating or input shorted to ground ....................................................... -35 V dc

Transient .................................................................................................. -43 V dc 2/

Storage temperature range.......................................................................... -65°C to +150°C

Lead temperature (soldering, 10 seconds) .................................................. +300°C

Power dissipation (P

= +25°C:

Cases M, N, T, U, Z, 4, and 5 .............................................................. 15 W

Cases X and 2 ...................................................................................... 2 W

Case Y.................................................................................................. 20 W

= +25°C:

Cases M, T, U, and Z ........................................................................... 3.0 W

Case N ................................................................................................. 15.0 W

Case X.................................................................................................. 1.0 W

Case Y.................................................................................................. 3.6 W

Case 2 .................................................................................................. 1040 mW

Case 4 ................................................................................................. 1.7 W

Case 5 ................................................................................................. 1.3 W

Junction temperature (T

)............................................................................ +150°C 3/

Thermal resistance, junction-to-case (θ

Case M .................................................................................................... 5.5°C/W

Cases N and T ......................................................................................... 3.5°C/W

Case U ..................................................................................................... 4.2°C/W

Case X ..................................................................................................... 15°C/W

Case Y ..................................................................................................... 3°C/W

Case Z ..................................................................................................... 6°C/W

Case 2...................................................................................................... 25°C/W

Case 4 ..................................................................................................... 5.1°C/W

Case 5 ..................................................................................................... 3.6°C/W

Thermal resistance, junction-to-ambient (θ

Cases M, T, U, and Z (device type 01)..................................................... 42°C/W

Cases N, X, and 2 .................................................................................... 120°C/W

Case Y ..................................................................................................... 35°C/W

Case 4 ..................................................................................................... 60°C/W

Case 5 ..................................................................................................... 80°C/W

1.4 Recommended operating conditions.

Input voltage range (V

) ............................................................................. -7.5 V dc to -20 V dc

Ambient operating temperature range (T

).................................................. -55°C to +125°C

1.5 Radiation features: 4/

Maximum total dose available (dose rate = 50 – 300 rads(Si)/s) ................. 300 Krads (Si)

_____

2/ The 43-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage.

Since the regulator’s maximum current capability is reduced, the output may fall out of regulation at high input voltages

under nominal loading.

3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever the

device junction temperature is in excess of +150°C.

4/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.

Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,

method 1019, condition A.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88746

SHEET

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 -

MIL-STD-1835 -

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

(Copies of these documents are available online at

http://assist.daps.dla.mil/quicksearch/

http://assist.daps.dla.mil

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A “Q” or “QML” certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.3 herein and on figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 3.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88746

SHEET

Recommended Resources

Do you know about the YTSwitch-6 LED driver IC with high efficiency and extremely low standby power?

Design of voice recording and playback circuit module composed of HY560

Electric rice cooker circuit diagram Type III circuit diagram

Electronic interlock switch using CD4017

Simple EKG Calibrator

845ddr computer motherboard circuit diagram_66

A speaker that produces sound through resonance: Innosound has no speaker or cabinet. Its sound-generating principle is different from that of traditional speakers that rely on their own cabinets. It can produce perfect sound as long as it resonates...; xyh_521 Creative Market

Regarding suggestions for active medical section, welcome to criticize: Since the medical electronics section is not well-received, I want to hold an event to increase its popularity. The event is initially planned to let me offer suggestions for medical electronics. I su...; 梦之旅 Suggestions & Announcements

Request the programming method of the LED text dot matrix display page animation switching function.: I recently developed an LED dot matrix screen. The static display is very stable, but I have no idea about the dynamic display. I have never worked with dot matrix screens before, so I would like to a...; 大赛 Embedded System

Request Sample: :) I want to apply for a sample...; hjhjlll NXP MCU

Question about the failure of eQEP to capture Z signal after TMS320F28335 watchdog reset: Dear counting engineers: I use a 2048-line encoder and 28335 to calculate the motor speed. After the program watchdog is reset, I fail to capture the encoder Z signal (index signal), while the capture...; Alex Microcontroller MCU

Frequently asked questions and answers in company HR interviews: Question 1: "Please introduce yourself" Ideas: 1. This is a must for the interview. 2. The content of the introduction should be consistent with your resume. 3. The expression should be as colloquial ...; xujian2000 Talking about work

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components