The UT54ACS109 and the UT54ACTS109 are dual J-K positive
triggered flip-flops. A low level at the preset or clear inputs sets
or resets the outputs regardless of the other input levels. When
preset and clear are inactive (high), data at the J and K input
meeting the setup time requirements are transferred to the out-
puts on the positive-going edge of the clock pulse. Following
the hold time interval, data at the J and K input can be changed
without affecting the levels at the outputs. The flip-flops can
perform as toggle flip-flops by grounding K and tying J high.
They also can perform as D flip-flops if J and K are tied together.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
PRE
L
H
L
H
H
H
H
H
CLR
H
L
L
H
H
H
H
H
CLK
X
X
X
↑
↑
↑
↑
L
J
X
X
X
L
H
L
H
X
K
X
X
X
L
L
H
H
X
OUTPUT
Q
H
L
H
L
1
PINOUTS
16-Pin DIP
Top View
CLR1
J
K1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLR2
J2
K2
CLK2
PRE2
Q2
Q2
16-Lead Flatpack
Top View
CLR1
J1
K1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLR2
J2
K2
CLK2
PRE2
Q2
Q2
LOGIC SYMBOL
Q
L
H
H
1
PRE1
J1
CLK1
K1
CLR1
PRE2
J2
CLK2
(5)
(2)
(4)
(3)
(1)
(11)
(14)
(12)
S
J1
C1
K1
R
(6)
Q1
(7)
Q1
H
Toggle
(10)
Q2
No Change
H
L
(13)
K2
(15)
CLR2
(9)
Q2
No Change
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and
IEC Publication 617-12.
Note:
1. The output levels in this configuration are not guaranteed to meet the minimum
levels for V
OH
if the lows at preset and clear are near V
IL
maximum. In
addition, this configuration is nonstable; that is, it will not persist when either
preset or clear returns to its inactive (high) level.
1
LOGIC DIAGRAM
PRE
CLK
Q
J
Q
K
CLR
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6 (ACTS109)
5.0E5 (ACS109)
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8,9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
2.0
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
I
OS
I
OL
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All ACTS specifications are valid for radiation dose <1E6 rads(Si), and all ACS specifications are valid for radiation dose <5E5 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
Part of the content is quoted from "ZTE Circuit Design Specifications" From Baidu Library[/color][/size][/font][/align][align=left][font=Helvetica Neue, Helvetica, Hiragino Sans GB, Microsoft YaHei, A...
[i=s]This post was last edited by lb8820265 on 2022-3-20 10:05[/i]The Raspberry Pi car is controlled by the UDP communication protocol of the mobile phone, which means that the IP address of the car n...
The attachment gives some projects made by several college students using msp430, including circuit diagrams and source code, hoping to provide help to msp430 beginners...
As early as the 1960s, people began to study and develop embedded operating systems. But it was not until recently that it was mentioned more and more in China. Its increasing importance in fields tha...
1 Design principle - To meet the maximum impedance mismatch, the insertion loss should be increased as much as possible, that is, the reflection of the signal should be increased as much as possible. ...
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
On August 20th, Tiantai Robotics Co., Ltd., along with strategic partners including Shandong Future Robotics Technology Co., Ltd., Shandong Future Data Technology Co., Ltd., and Gangzai Robotics Gr...[Details]
Since the beginning of this year, price wars have intensified, new models have been launched one after another, used cars with zero kilometers have become a hot topic, and the industry's internal c...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
While the current industry consensus is that autonomous vehicles are robots and that their systems are managed using robotics-developed thinking, there are also cases where autonomous driving is ac...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Charging is an essential topic for electric vehicles. Batteries are a core component of new energy vehicles. So, what's the optimal charge level for electric vehicles? Based on current battery tech...[Details]
Nascent Micro is launching devices covering a wide range of power applications, including gallium nitride (GaN) drivers, dual-channel automotive drivers, and battery protection MOSFETs.
...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
introduction
In today's busy society, people experience chronic high stress, which in turn poses a significant threat to our health. Therefore, effectively relieving stress has become a pr...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
