20ns (3.3 volt supply) maximum address access time
Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
TTL compatible inputs and output levels, three-state
bidirectional data bus
Typical radiation performance
- Total dose: 50krads
- >100krads(Si), for any orbit, using Aeroflex UTMC
patented shielded package
- SEL Immune >80 MeV-cm
2
/mg
- LET
TH
(0.25) = >10 MeV-cm
2
/mg
- Saturated Cross Section cm
2
per bit, 5.0E-9
- <1E-8 errors/bit-day, Adams 90% geosynchronous
heavy ion
Packaging options:
- 36-lead ceramic flatpack (3.42 grams)
- 36-lead flatpack shielded (10.77 grams)
Standard Microcircuit Drawing 5962-99607
- QML T and Q compliant
INTRODUCTION
The QCOTS
TM
UT8Q512 Quantified Commercial Off-the-
Shelf product is a high-performance CMOS static RAM
organized as 524,288 words by 8 bits. Easy memory expansion
is provided by an active LOW Chip Enable (E), an active LOW
Output Enable (G), and three-state drivers. This device has a
power-down feature that reduces power consumption by more
than 90% when deselected
.
Writing to the device is accomplished by taking Chip Enable
one (E) input LOW and Write Enable (W) inputs LOW. Data on
the eight I/O pins (DQ
0
through DQ
7
) is then written into the
location specified on the address pins (A
0
through A
18
). Reading
from the device is accomplished by taking Chip Enable one (E)
and Output Enable (G) LOW while forcing Write Enable (W)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E, HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOWand W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT8Q512 SRAM Block Diagram
1
DEVICE OPERATION
A0
A1
A2
A3
A4
E
DQ0
DQ1
V
DD
V
SS
DQ2
DQ3
W
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
The UT8Q512 has three control inputs called Enable 1 (E), Write
Enable (W), and Output Enable (G); 19 address inputs, A(18:0);
and eight bidirectional data lines, DQ(7:0). E Device Enable
controls device selection, active, and standby modes. Asserting
E enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. 25ns SRAM Pinout (36)
1
0
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Enable
Write Enable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) and E less than V
IL
(max) defines a read cycle. Read access time is measured from
the latter of Device Enable, Output Enable, or valid address to
valid data output.
SRAM Read Cycle 1, the Address Access in figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Device
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 3b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 3c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable - Controlled Access in figure
4a, is defined by a write terminated by W going high, with E
still active. The write pulse width is defined by t
WLWH
when the
write is initiated by W, and by t
ETWH
when the write is initiated
by E. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable - Controlled Access in figure
4b, is defined by a write terminated by the latter of E going
inactive. The write pulse width is defined by t
WLEF
when the
write is initiated by W, and by t
ETEF
when the write is initiated
by the E going active. For the W initiated write, unless the
outputs have been previously placed in the high-impedance state
by G, the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
Table 2. Typical Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1E-8
krad(Si) nominal
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 4.6V
-0.5 to 4.6V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
PARAMETER
Positive supply voltage
Case temperature range
LIMITS
3.0 to 3.6V
(C) screening: -55° to +125°C
(E) screening: -40° to +125°C
V
IN
DC input voltage
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(-55°C to +125°C for (C) screening and -40
o
C to +125
o
C for (W) screening) (V
DD
= 3.3V + 0.3)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(TTL)
(TTL)
I
OL
= 8mA, V
DD
=3.0V (TTL)
I
OL
= 200µA,V
DD
=3.0V (CMOS)
I
OH
= -4mA,V
DD
=3.0V (TTL)
I
OH
= -200µA,V
DD
=3.0V (CMOS)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
SS
< V
IN
< V
DD,
V
DD
= V
DD
(max)
0V < V
O
< V
DD
V
DD
= V
DD
(max)
G = V
DD
(max)
0V < V
O
< V
DD
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E = V
DD
- 0.5
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
-55°C and 25°C
-40
o
C and 25
o
C
+125°C
-2
-2
2.4
V
DD
-0.10
10
12
2
2
CONDITION
MIN
2.0
0.8
0.4
0.08
MAX
UNIT
V
V
V
V
V
V
pF
pF
µA
µA
I
OS2, 3
I
DD
(OP)
Short-circuit output current
Supply current operating
@ 1MHz
-90
90
125
mA
mA
I
DD1
(OP)
Supply current operating
@40MHz
180
mA
I
DD2
(SB)
Nominal standby supply current
@0MHz
6
6
40
mA
mA
mA
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
Embedded systems are used in a large number of electronic devices, and their design involves both hardware and software technology. As computer technology has advanced, its technology has become incre...
@Northern China[/url] [/size] [url=https://bbs.eeworld.com.cn/thread-566869-1-1.html][size=4][X-NUCLEO-IKS01A2 Review] Introduction to the development environment[/size][/url] [url=https://bbs.eeworld...
[size=5] 1. This is my first time buying chips on TI's official website. Can you help me check if there is any problem with this order? [/size][size=5] 2. Where can I see if the product has been shipp...
Environment: OS: win_xp2 File system: C drive FAT32, install keil, D drive NTFS, store programs and compilation results, etc. Compiler: keil uVision 2, uVision 3, uVision 4 have all been used. The fil...
On August 18th, Galaxis, a specialist in integrated intelligent intralogistics robotics, officially unveiled its next-generation, ultra-narrow aisle forklift mobile robot, the "VFR Ultra-Narrow Ser...[Details]
A half-bridge is an inverter topology for converting DC to AC. A typical half-bridge circuit consists of two controller switches, a three-wire DC power supply, two feedback diodes, and two capacito...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
Compiled from semiengineering
The industry is increasingly concerned about power consumption in AI, but there are no simple solutions. This requires a deep understanding of software and ...[Details]
introduction
The widespread use of air conditioner communication circuits began with the rise of household inverter air conditioners. With China's energy conservation and emission reduction in...[Details]
introduction
Whether in the automotive entertainment or home theater system markets, consumers continue to demand more channels and speakers, each capable of handling higher audio po...[Details]
Chip architecture licensing company ARM has hired Amazon's AI chip chief Rami Sinno to help advance its plan to develop its own complete chip, people familiar with the matter said, according to Reu...[Details]
1. Introduction to power amplifier circuit
1. Generally speaking, the main function of a power amplifier circuit is to allow the load to obtain maximum power without distorting the signal or c...[Details]
PLCs are one of the three pillars of modern industry, offering highly reliable and widely used industrial control products. In medium- to large-scale modular PLCs, the CPU module (central processin...[Details]
Robots are rapidly being deployed in diverse scenarios. Flexible, easy-to-use, and fast-to-deploy robots can be quickly adapted to diverse application scenarios across various industries, making th...[Details]
2025 World Congress
Officially opens
Recently, over 220 robotics companies from around the world gathered at the Beijing Beiren Yichuang International Exhibition Center to officially lau...[Details]
Baolong Technology recently secured another contract for intelligent suspension system components for a high-end model from a renowned international electric vehicle manufacturer. Building on its p...[Details]
Ever since smartphones became popular, their battery life has become a major concern. Although current phones often have large batteries of 3,000 to 4,000 mAh, heavy users still have to charge thei...[Details]
A speaker box, also known as a loudspeaker enclosure, combines high, mid, and low-frequency speakers within a specially designed enclosure. A crossover network routes high, mid, and low-frequency s...[Details]
To address the challenges of traditional discrete solutions in automotive intelligent actuators, such as high complexity, high cost, and insufficient reliability,
Naxin Microelectronics has lau...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
