The outputs of the UT7R995 can be configured to run at fre-
quencies ranging from 6 MHz to 200 MHz. Each output bank
has the ability to run at separate frequencies and with various
phase skew. Depending upon the output used for feedback to
the PLL, numerous clock division and multiplication options
exist.
The following discussion and list of tables will summarize the
available configuration options for the UT7R995. Tables 1
through 11, are relevant to the following configuration discus-
sions.
Table 1. Feedback Divider Settings (N-factor)
Table 2. Reference Divider Settings (R-Factor)
Table 3. Output Divider Settings - Bank 3 (K-factor)
Table 4. Output Divider Settings - Bank 4 (M-Factor)
Table 5. Frequency Divider Summary
Table 6. Calculating Output Frequency Settings
Table 7. Frequency Range Select
Table 8. Multiplication Factor (MF) Calculation
Table 9. Output Skew Settings
Table 10: Signal Propagation Delays in Various Media
Table 11. PE/HD Settings
Table 12. Power Supply Constraints
1.1 Divider Configuration Settings:
The feedback input divider is controlled by the 3-level DS[1:0]
pins as indicated in Table 1 and the reference input divider is
controlled by the 3-level PD/DIV pin as indicated in Table 2.
Although the Reference divider will continue to operate when
the UT7R995 is in the standard TEST mode of operation, the
Feedback Divider will not be available.
Table 1: Feedback Divider Settings (N-factor)
DS[1:0]
LL
LM
LH
ML
MM
MH
HL
HM
HH
Table 2: Reference Divider Settings (R-factor)
PD/DIV
LOW
1
MID
HIGH
Operating Mode
Powered Down
Normal Operation
Normal Operation
Reference Input
Divider -
(R)
Not Applicable
2
1
Note: 1.
When PD/DIV = LOW, the device enters power-down mode.
In addition to the reference and feedback dividers, the
UT7R995 includes output dividers on Bank 3 and Bank 4,
which are controlled by 3F[1:0] and 4F[1:0] as indicated in Ta-
bles 3 and 4, respectively.
Table 3: Output Divider Settings - Bank 3 (K-factor)
3F(1:0)
LL
HH
Bank 3 Output Divider -
(K)
2
4
Note: 1.
These states are used to program the phase of the respective banks.
Please see Equation 1 along with Tables 8 and 9.
PM
4F[1:0]
LL
Other
1
Table 4: Output Divider Settings - Bank 4 (M-factor)
Bank 4 Output Divider
(M)
2
1
2
3
4
5
1
EV
Feedback Input
Divider -
(N)
Permitted Output
Divider (K or M)
Connected to FB
1 or 2
1
EL
O
Note: 1.These
states are used to program the phase of the respective banks.
Please see Equation 1 along with Tables 8 and 9.
Each of the four divider options and their respective settings are
summarized in Table 5. By applying the divider options in Ta-
ble 5 to the calculations shown in Table 6, the user determines
the proper clock frequency for every output bank.
Table 5: Frequency Divider Summary
Division
Factors
N
R
K
M
D
1, 2, or 4
1 or 2
1, 2, or 4
1 or 2
1 or 2
1
1
IN
6
EN
T
Other
1
1
Available Divider Settings
1, 2, 3, 4, 5, 6, 8, 10, 12
1, 2
1, 2, 4
1, 2
8
10
12
3
Table 6: Calculating Output Frequency Settings
Configuration
Clock Output
Connected to FB
1Qn or 2Qn
3Qn
4Qn
Output Frequency
1Q[1:0]
1
and
2Q[1:0]
1
(N/R) * f
XTAL
(N/R) * K * f
XTAL
(N/R) * M * f
XTAL
(N/R) * (1/K) * f
XTAL
(N/R) * f
XTAL
(N/R) * (M/K) * f
XTAL
(N/R) * (1/M) * f
XTAL
(N/R) * (K/M) * f
XTAL
(N/R) * f
XTAL
3Q[1:0]
4Q[1:0]
Notes:
1. These outputs are undivided copies of the VCO clock. Therefore, the formulas in this column can be used to calculate the nominal VCO operating frequency (f
NOM
)
at a given reference frequency (f
XTAL
) and the divider and feedback configuration. The user must select a configuration and a reference frequency that will generate
a VCO frequency that is within the range specified by FS pin. Please see Table 7.
1.2 Frequency Range and Skew Selection:
The PLL in the UT7R995 operates within three nominal fre-
quency ranges. Each of which is selectable by the user through
the 3-level FS control pin. The selected FS settings given in Ta-
ble 7 determine the nominal operating frequency range of the
divide-by-one outputs of the UT7R995. Reference the first col-
umn of equation in Table 6 to calculate the value of f
NOM
for
any given feedback clock.
Table 7: Frequency Range Select
FS
L
M
H
Selectable output skew is in discrete increments of time unit
(t
U
). The value of t
U
is determined by the FS setting and the
maximum nominal frequency. The equation to be used to deter-
mine the t
U
value is as follows:
T
t
u
Equation 1.
=
1
(f
NOM
* MF)
Nominal PLL Frequency Range
(f
NOM
)
24 to 50 MHz
48 to 100MHz
96 to 200 MHz
IN
D
EV
4
EL
O
PM
The f
NOM
term, selected by the FS signal, is found in Table 7,
and the multiplication factor (MF), also determined by FS, is
shown in Table 8.
After calculating the time unit (t
U
) based on the nominal PLL
frequency (f
NOM
) and multiplication factor (MF), the circuit
designer plans routing requirements of each clock output and its
respective destination receiver. With an understanding of signal
propagation delays through a conductive medium (see Table
10), the designer specifies trace lengths which ensure a signal
propagation delay that is equal to one of the t
U
multiples show
in Table 9. For each output bank, the t
U
skew factors are select-
ed with the tri-level, bank-specific, nF[1:0] pins.
EN
Table 8: MF Calculation
FS
L
M
H
MF
32
16
8
f
NOM
at which t
U
is 1.0ns
31.25 MHz
62.5 MHz
125 MHz
Table 10: Examples of Common Signal Propagation Delays
found in Various Mediums
Medium
Air (Radio Waves)
Coax. Cable (75% Velocity)
Coax. Cable (66% Velocity)
Propagation
Dielectric
Delay (ps/inch) Constant
85
113
129
140 - 180
180
240 - 270
1.0
1.8
2.3
2.8 - 4.5
4.5
8 - 10
Table 9: Output Skew Settings
nF[1:0]
LL
1, 2
FR4 PCB, Outer Trace
Skew
1Q[1:0], 2Q[1:0]
-4t
U
-3t
U
-2t
U
-1t
U
Zero Skew
+1t
U
+2t
U
+3t
U
+4t
U
Skew
3Q[1:0]
Divide by 2
-6t
U
-4t
U
-2t
U
Zero Skew
+2t
U
+4t
U
+6t
U
Divide by 4
Skew
4Q[1:0]
Divide by 2
-6t
U
-4t
U
-2t
U
Zero Skew
FR4 PCB, Inner Trace
Alumina PCB, Inner Trace
LM
LH
ML
MM
MH
HL
HM
HH
2
+4t
U
+6t
U
Inverted
3
IN
D
EV
EL
5
O
Notes:
1. nF[1:0] = LL disables bank specific outputs if TEST=MID and sOE = HIGH.
2. When TEST=MID or HIGH, the Divide-by-2, Divide-by-4, and Inversion
options function as defined in Table 9.
3. When 4Q[1:0] are set to run inverted (4F[1:0] = HH), sOE disables these out-
puts HIGH when PE/HD = HIGH or MID, sOE disables them LOW when
[align=left][color=#000]In my last blog post[/url][/color]I talked about the different types of digital filters commonly used in delta-sigma analog-to-digital converters (ADCs). In this post, I will f...
[size=2]Next Tuesday, TI will introduce its latest SimpleLink wireless MCU products: CC13X2 and CC26X2 at the forum. The highlights are low power consumption and multi-band. The official publicity of ...
The green box is equivalent to VEQ, and the rest of the rectifier and BUCK circuit is equivalent to this Rload. So how do I calculate this Rload? The switch signal parameters are shown in Figure 1....
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
Reflow soldering, a common soldering method in modern electronics manufacturing, primarily melts solder paste and pads to form solder joints. With technological advancements, soldering equipment ha...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
Overview
As handheld voice communication devices become more and more popular, they are increasingly used in noisy environments, such as airports, busy roads, crowded bars, etc. In such noisy ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
A patent disclosed by Ford proposes replacing traditional segmented side curtain airbags with integrated full-width side curtain airbags that span the side of the vehicle and can be deployed simult...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
