The outputs of the UT7R995 can be configured to run at fre-
quencies ranging from 6 MHz to 200 MHz. Each output bank
has the ability to run at separate frequencies and with various
phase skew. Depending upon the output used for feedback to
the PLL, numerous clock division and multiplication options
exist.
The following discussion and list of tables will summarize the
available configuration options for the UT7R995. Tables 1
through 11, are relevant to the following configuration discus-
sions.
Table 1. Feedback Divider Settings (N-factor)
Table 2. Reference Divider Settings (R-Factor)
Table 3. Output Divider Settings - Bank 3 (K-factor)
Table 4. Output Divider Settings - Bank 4 (M-Factor)
Table 5. Frequency Divider Summary
Table 6. Calculating Output Frequency Settings
Table 7. Frequency Range Select
Table 8. Multiplication Factor (MF) Calculation
Table 9. Output Skew Settings
Table 10: Signal Propagation Delays in Various Media
Table 11. PE/HD Settings
Table 12. Power Supply Constraints
1.1 Divider Configuration Settings:
The feedback input divider is controlled by the 3-level DS[1:0]
pins as indicated in Table 1 and the reference input divider is
controlled by the 3-level PD/DIV pin as indicated in Table 2.
Although the Reference divider will continue to operate when
the UT7R995 is in the standard TEST mode of operation, the
Feedback Divider will not be available.
Table 1: Feedback Divider Settings (N-factor)
DS[1:0]
LL
LM
LH
ML
MM
MH
HL
HM
HH
Table 2: Reference Divider Settings (R-factor)
PD/DIV
LOW
1
MID
HIGH
Operating Mode
Powered Down
Normal Operation
Normal Operation
Reference Input
Divider -
(R)
Not Applicable
2
1
Note: 1.
When PD/DIV = LOW, the device enters power-down mode.
In addition to the reference and feedback dividers, the
UT7R995 includes output dividers on Bank 3 and Bank 4,
which are controlled by 3F[1:0] and 4F[1:0] as indicated in Ta-
bles 3 and 4, respectively.
Table 3: Output Divider Settings - Bank 3 (K-factor)
3F(1:0)
LL
HH
Bank 3 Output Divider -
(K)
2
4
Note: 1.
These states are used to program the phase of the respective banks.
Please see Equation 1 along with Tables 8 and 9.
PM
4F[1:0]
LL
Other
1
Table 4: Output Divider Settings - Bank 4 (M-factor)
Bank 4 Output Divider
(M)
2
1
2
3
4
5
1
EV
Feedback Input
Divider -
(N)
Permitted Output
Divider (K or M)
Connected to FB
1 or 2
1
EL
O
Note: 1.These
states are used to program the phase of the respective banks.
Please see Equation 1 along with Tables 8 and 9.
Each of the four divider options and their respective settings are
summarized in Table 5. By applying the divider options in Ta-
ble 5 to the calculations shown in Table 6, the user determines
the proper clock frequency for every output bank.
Table 5: Frequency Divider Summary
Division
Factors
N
R
K
M
D
1, 2, or 4
1 or 2
1, 2, or 4
1 or 2
1 or 2
1
1
IN
6
EN
T
Other
1
1
Available Divider Settings
1, 2, 3, 4, 5, 6, 8, 10, 12
1, 2
1, 2, 4
1, 2
8
10
12
3
Table 6: Calculating Output Frequency Settings
Configuration
Clock Output
Connected to FB
1Qn or 2Qn
3Qn
4Qn
Output Frequency
1Q[1:0]
1
and
2Q[1:0]
1
(N/R) * f
XTAL
(N/R) * K * f
XTAL
(N/R) * M * f
XTAL
(N/R) * (1/K) * f
XTAL
(N/R) * f
XTAL
(N/R) * (M/K) * f
XTAL
(N/R) * (1/M) * f
XTAL
(N/R) * (K/M) * f
XTAL
(N/R) * f
XTAL
3Q[1:0]
4Q[1:0]
Notes:
1. These outputs are undivided copies of the VCO clock. Therefore, the formulas in this column can be used to calculate the nominal VCO operating frequency (f
NOM
)
at a given reference frequency (f
XTAL
) and the divider and feedback configuration. The user must select a configuration and a reference frequency that will generate
a VCO frequency that is within the range specified by FS pin. Please see Table 7.
1.2 Frequency Range and Skew Selection:
The PLL in the UT7R995 operates within three nominal fre-
quency ranges. Each of which is selectable by the user through
the 3-level FS control pin. The selected FS settings given in Ta-
ble 7 determine the nominal operating frequency range of the
divide-by-one outputs of the UT7R995. Reference the first col-
umn of equation in Table 6 to calculate the value of f
NOM
for
any given feedback clock.
Table 7: Frequency Range Select
FS
L
M
H
Selectable output skew is in discrete increments of time unit
(t
U
). The value of t
U
is determined by the FS setting and the
maximum nominal frequency. The equation to be used to deter-
mine the t
U
value is as follows:
T
t
u
Equation 1.
=
1
(f
NOM
* MF)
Nominal PLL Frequency Range
(f
NOM
)
24 to 50 MHz
48 to 100MHz
96 to 200 MHz
IN
D
EV
4
EL
O
PM
The f
NOM
term, selected by the FS signal, is found in Table 7,
and the multiplication factor (MF), also determined by FS, is
shown in Table 8.
After calculating the time unit (t
U
) based on the nominal PLL
frequency (f
NOM
) and multiplication factor (MF), the circuit
designer plans routing requirements of each clock output and its
respective destination receiver. With an understanding of signal
propagation delays through a conductive medium (see Table
10), the designer specifies trace lengths which ensure a signal
propagation delay that is equal to one of the t
U
multiples show
in Table 9. For each output bank, the t
U
skew factors are select-
ed with the tri-level, bank-specific, nF[1:0] pins.
EN
Table 8: MF Calculation
FS
L
M
H
MF
32
16
8
f
NOM
at which t
U
is 1.0ns
31.25 MHz
62.5 MHz
125 MHz
Table 10: Examples of Common Signal Propagation Delays
found in Various Mediums
Medium
Air (Radio Waves)
Coax. Cable (75% Velocity)
Coax. Cable (66% Velocity)
Propagation
Dielectric
Delay (ps/inch) Constant
85
113
129
140 - 180
180
240 - 270
1.0
1.8
2.3
2.8 - 4.5
4.5
8 - 10
Table 9: Output Skew Settings
nF[1:0]
LL
1, 2
FR4 PCB, Outer Trace
Skew
1Q[1:0], 2Q[1:0]
-4t
U
-3t
U
-2t
U
-1t
U
Zero Skew
+1t
U
+2t
U
+3t
U
+4t
U
Skew
3Q[1:0]
Divide by 2
-6t
U
-4t
U
-2t
U
Zero Skew
+2t
U
+4t
U
+6t
U
Divide by 4
Skew
4Q[1:0]
Divide by 2
-6t
U
-4t
U
-2t
U
Zero Skew
FR4 PCB, Inner Trace
Alumina PCB, Inner Trace
LM
LH
ML
MM
MH
HL
HM
HH
2
+4t
U
+6t
U
Inverted
3
IN
D
EV
EL
5
O
Notes:
1. nF[1:0] = LL disables bank specific outputs if TEST=MID and sOE = HIGH.
2. When TEST=MID or HIGH, the Divide-by-2, Divide-by-4, and Inversion
options function as defined in Table 9.
3. When 4Q[1:0] are set to run inverted (4F[1:0] = HH), sOE disables these out-
puts HIGH when PE/HD = HIGH or MID, sOE disables them LOW when
I look forward to two things every day: the people I get to work with and the technology I get to use. However, I also sometimes take a moment to reflect on where high voltage innovation is headed in ...
I use +5V to power AD421, why does the chip heat up immediately when the power is turned on? The positive and negative terminals of the chip are connected correctly. Does anyone know about this situat...
Dear brothers and sisters: In the figure below, why is the address of the digital-to-analog converter DAC0832 connected to the 8031 microcontroller E000H? Please give me some advice! Thank you!...
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
Nios II is a configurable 16-/32-bit RISC processor. Combined with a rich set of peripheral-specific instructions and hardware acceleration units, it provides a highly flexible and powerful SOPC sy...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
introduction
As core electronic components used in vastly different fields, automotive-grade chips and mobile/consumer-grade chips exhibit significant differences in their...[Details]
Compiled from semiengineering
The industry is increasingly concerned about power consumption in AI, but there are no simple solutions. This requires a deep understanding of software and ...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
Blackfin® 16-/32-bit embedded processors offer high performance, low power consumption, flexible software features, and scalability, making them suitable for converged applications such as multi-fo...[Details]
The motor is a very important component for new energy vehicles. In terms of vehicle power, pure electric vehicles use electric motors instead of traditional diesel/gasoline engines. For electric v...[Details]
According to foreign media reports, Apple is secretly evaluating several artificial intelligence hardware concepts, including smart home displays, security devices and a desktop robot, of which the...[Details]
On August 19, Reuters reported that people familiar with the matter said that Nvidia is developing a new AI chip based on its latest Blackwell architecture for the Chinese market. The performance o...[Details]
Mathematical functions are very important and are used in many situations such as analog quantity processing and PID control.
(12) Calculate sine value instruction (SIN)
The "Calculate Si...[Details]
introduction
Commercial air conditioner PCBs involve both high-voltage and low-voltage power. The power supply for commercial air conditioners often passes through the controller. This forces ...[Details]
Chip architecture licensing company ARM has hired Amazon's AI chip chief Rami Sinno to help advance its plan to develop its own complete chip, people familiar with the matter said, according to Reu...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
