The UT54ACS165E is an 8-bit serial shift register that, when clocked,
shifts the data toward serial output Q
H
. Parallel-in access to each stage
is provided by eight individual data inputs that are enabled by a low
level at the SH/LD input. The devices feature a clock inhibit function
and a complemented serial output Q
H
.
Clocking is accomplished by a low-to-high transition of the CLK input
while SH/LD is held high and CLK INH is held low. The functions of
the CLK and CLK INH (clock inhibit) inputs are interchangeable.
Since a low CLK input and a low-to-high transition of CLK INH will
also accomplish clocking, CLK INH should be changed to the high
level only while the CLK input is high. Parallel loading is disabled
when SH/LD is held high. Parallel inputs to the registers are enabled
while SH/LD is low independently of the levels of CLK, CLK INH or
SER inputs.
The device is characterized over the full military temperature range of
-55°C to +125°C.
Note:
1. Q
n
= The state of the referenced output one setup time prior to the Low-to-
High clock transition.
LOGIC SYMBOL
(1)
SH/LD
(15)
CLK INH
(2)
CLK
(10)
SER
(11)
A
(12)
B
(13)
C
(14)
D
(3)
E
(4)
F
(5)
G
(6)
H
SRG8
C1 (LOAD)
≥1
C2/
PINOUT
16-Lead Flatpack
Top View
SH/LD
CLK
E
F
G
H
Q
H
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLK INH
D
C
B
A
SER
Q
H
2D
1D
1D
1D
(9)
Q
(7)
H
Q
H
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
1
LOGIC DIAGRAM
A
(11
)
SH/LD
B
(12)
C
(13)
D
(14)
E
(3)
F
(4)
G
(5)
H
(6)
(1)
CLK INH
CLK
(15)
(2)
S
C
SER
S
C
D Q
B
S
C
DQ
C
S
C
D Q
D
S
C
D Q
E
S
C
D Q
F
S
C
D Q
G
S
C
(9)
Q
H
(10
)
D
Q
A
(7)
D Q
H
R
R
R
R
R
R
R
R
Q
H
RADIATION HARDNESS SPECIFICATIONS
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+ .3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these
or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
3.0 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACS165E
7
( V
DD
= 3.0V to 5.5V; V
SS
= 0V
6
; -55°C < T
C
< +125°C)
SYMBOL
V
IL
Description
Low-level input voltage
1
High-level input voltage
1
CONDITION
VDD
3.0V
5.5V
V
IH
3.0V
5.5V
I
IN
V
OL
Input leakage current
Low-level output voltage
3
High-level output voltage
3
Short-circuit output current
2 ,4
V
IN
= V
DD
or V
SS
I
OL
= 100µA
5.5V
3.0V
4.5V
V
OH
I
OH
= -100µA
3.0V
4.5V
I
OS
V
O
= V
DD
and V
SS
3.0V
5.5V
I
OL
Low level output current
9
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
I
OH
High level output current
9
V
IN
= V
DD
or V
SS
V
OH
= V
DD
-0.4V
P
total
I
DDQ
C
IN
C
OUT
Power dissipation
2, 8
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
C
L
= 50pF
V
IN
= V
DD
or V
SS
ƒ
= 1MHz
ƒ
= 1MHz
3.0V
5.5V
3.0V
5.5V
5.5V
3.0V
5.5V
0V
0V
2.75
4.25
-100
-200
6
8
-6
-8
2.9
1.16
10
15
15
mW/
MHz
µA
pF
pF
mA
100
200
mA
mA
2.1
3.85
-1
1
0.25
0.25
V
µA
V
MIN
MAX
0.9
1.65
V
UNIT
V
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤5.0E5
amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765pF/
MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si) per MIL-STD-883 Method 1019 Condition B.
8. Power dissipation specified per switching output.
9. This value is guaranteed based on characterization data, but not tested.
I use STM32F7 in my project. I have two questions: 1. Are the IO ports of F7 5V tolerant? 2. What download tool do I use to develop F7 programs? Is STLINK okay? Thanks!...
//Similarly, using lcd1602 display, I will not describe the program here, there is #include "lcd1602.h" #define Num_of_Results 32 static uint results[Num_of_Results]; uchar a[10]="0123456789"; uchar b...
To many readers, this article may be laughable. However, the concept of Ethernet in real-time applications is the most optimistic. Ethernet is not reliable because it does not establish a unique and d...
#16019-D file "C:/ti/ccsv6/tools/compiler/c2000_6.2.5/lib/rts2800.lib" specifies large memory model, which is not compatible with small memory model specified in a previous file or on the command line...
The FPGA uses StratixII GX, and the RAM resources are M512 (32*18bits), M4K (128*36bits) and M-RAM (4K*144bits). I instantiate a 64*48 FIFO and it takes up 2 M4Ks; I instantiate a 128*48 FIFO and it t...
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
With the increasing popularity of automated equipment, linear modules, a common auxiliary device for automated equipment, have also seen a bright future. In particular, in recent years, many small ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
The drive shaft is a high-speed, low-support rotating body, so its dynamic balance is crucial. Generally, drive shafts undergo dynamic balancing tests and adjustments on a balancing machine before ...[Details]
This article uses the Allwinner T507 quad-core automotive-grade processor as the development board. This article explains how to configure Ethernet for the T507 development board. Other boards may ...[Details]
The transition to SDVs (software-defined vehicles) involves more than just replacing parts; rather, it involves the organic connection of various elements, from internal vehicle systems to ext...[Details]
According to the latest financial report data, thanks to its leading position in advanced technology, TSMC's profit performance in the second quarter of 2025 was extremely impressive, with net prof...[Details]
• Standard message
1: Speed control
• Standard Telegram
2: Speed Control
• Standard Telegram
3: Speed/Position Control (used when the 1200 is configured as a TO)
...[Details]
System Principle
According to the average imbalance rate of the branch three-phase phase line load and the average value of the branch phase line current, the adjustment of the phase line load...[Details]
This article, part of Texas Instruments' "Power Supply Design Tips" series,
focuses on flyback converter design, discussing key design considerations for a 53VDC to 12V/5A continuous conduction...[Details]
In recent years, portable electronic devices such as mobile phones, digital cameras, music players, tablets, ultrabooks, and laptops have become almost a necessity, raising safety concerns. Besides...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
