Radiation-hardened design; total dose irradiation testing to
MIL-STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1Mrad(Si)
- Latchup immune (LET > 111 M eV-cm
2
/mg)
Packaging options:
- 16-lead flatpack (dual in-line)
Standard Microcircuit Drawing 5962-95834
- QML Q and V compliant part
Compatible with IEEE 1596.3SCI LVDS
Compatible with ANSI/TIA/EIA 644-1996 LVDS Standard
INTRODUCTION
The UT54LVDS032 Quad Receiver is a quad CMOS
differential line receiver designed for applications requiring
ultra low power dissipation and high data rates. The device
is designed to support data rates in excess of 155.5 Mbps
(77.7 MHz) utilizing Low Voltage Differential Signaling
(LVDS) technology.
The UT54LVDS032 accepts low voltage (340mV)
differential input signals and translates them to 5V TTL
output levels. The receiver supports a three-state function
that may be used to multiplex outputs. The receiver also
supports OPEN, shorted and terminated (100
Ω)
input fail-
safe. Receiver output will be HIGH for all fail-safe
conditions.
The UT54LVDS032 and companion quad line driver
UT54LVDS031 provides new alternatives to high power
pseudo-ECL devices for high speed point-to-point interface
applications.
q
q
q
q
R
IN1+
R
IN1-
+
R1
-
R
OUT1
R
IN2+
R
IN2-
+
R2
-
R
OUT2
R
IN3+
R
IN3-
+
R3
-
R
OUT3
R
IN4+
R
IN4-
EN
EN
+
R4
-
R
OUT4
Figure 1. UT54LVDS032 Quad Receiver Block Diagram
APPLICATIONS INFORMATION
The UT54LVDS032 receiver’s intended use is primarily in an
uncomplicated point-to-point configuration as is shown in
Figure 3. This configuration provides a clean signaling
environment for quick edge rates of the drivers. The receiver is
connected to the driver through a balanced media which may be
a standard twisted pair cable, a parallel pair cable, or simply
PCB traces. Typically, the characteristic impedance of the media
is in the range of 100Ω. A termination resistor of 100Ω should
be selected to match the media and is located as close to the
receiver input pins as possible. The termination resistor converts
the current sourced by the driver into voltages that are detected
by the receiver. Other configurations are possible such as a
multi-receiver configuration, but the effects of a mid-stream
connector(s), cable stub(s), and other impedance discontinuities,
as well as ground shifting, noise margin limits, and total
termination loading must be taken into account.
R
IN1-
R
IN1+
R
OUT1
EN
R
OUT2
R
IN2+
R
IN2-
V
SS
1
2
3
4
5
6
7
8
UT54LVDS032
Receiver
16
15
14
13
12
11
10
9
V
DD
R
IN4-
R
IN4+
R
OUT4
EN
R
OUT3
R
IN3+
R
IN3-
Figure 2. UT54LVDS032 Pinout
TRUTH TABLE
Enables
EN
L
EN
H
Input
R
IN+
- R
IN
-
X
V
ID
> 0.1V
V
ID
< -0.1V
Full Fail-safe
OPEN/SHORT or
Terminated
PIN DESCRIPTION
Pin No.
2, 6, 10, 14
1, 7, 9, 15
3, 5, 11, 13
4
12
16
8
Name
R
IN+
R
IN-
R
OUT
EN
EN
V
DD
V
SS
Description
Non-inverting receiver input pin
Inverting receiver input pin
Receiver output pin
Active high enable pin, OR-ed
with EN
Active low enable pin, OR-ed
with EN
Power supply pin, +5V + 10%
Ground pin
Output
R
OUT
Z
H
L
H
DATA
INPUT
ENABLE
1/4 UT54LVDS032
RT 100Ω
+
-
DATA
OUTPUT
1/4 UT54LVDS031
All other combinations
of ENABLE inputs
Figure 3. Point-to-Point Application
The UT54LVDS032 differential line receiver is capable of
detecting signals as low as 100mV, over a + 1V common-mode
range centered around +1.2V. This is related to the driver offset
voltage which is typically +1.2V. The driven signal is centered
around this voltage and may shift +1V around this center point.
The +1V shifting may be the result of a ground potential
difference between the driver’s ground reference and the
receiver’s ground reference, the common-mode effects of
coupled noise or a combination of the two. Both receiver input
pins should honor their specified operating input voltage range
of 0V to +2.4V (measured from each pin to ground).
2
Receiver Fail-Safe
The UT54LVDS032 receiver is a high gain, high speed device
that amplifies a small differential signal (20mV) to TTL logic
levels. Due to the high gain and tight threshold of the receiver,
care should be taken to prevent noise from appearing as a valid
signal.
The receiver’s internal fail-safe circuitry is designed to source/
sink a small amount of current, providing fail-safe protection (a
stable known state of HIGH output voltage) for floating,
terminated or shorted receiver inputs.
1.
Open Input Pins.
The UT54LVDS032 is a quad
receiver device, and if an application requires only 1, 2
or 3 receivers, the unused channel(s) inputs should be
left OPEN. Do not tie unused receiver inputs to ground
or any other voltages. The input is biased by internal high
value pull up and pull down resistors to set the output to
a HIGH state. This internal circuitry will guarantee a
HIGH, stable output state for open inputs.
2.
Terminated Input.
If the driver is disconnected (cable
unplugged), or if the driver is in a three-state condition,
the receiver output will again be in a HIGH state, even
with the end of cable 100Ω termination resistor across
the input pins. The unplugged cable can become a
floating antenna which can pick up noise. If the cable
picks up more than 10mV of differential noise, the
receiver may see the noise as a valid signal and switch.
To insure that any noise is seen as common-mode and
not differential, a balanced interconnect should be used.
Twisted pair cable offers better balance than flat ribbon
cable.
3.
Shorted Inputs.
If a fault condition occurs that shorts
the receiver inputs together, thus resulting in a 0V
differential input voltage, the receiver output remains in
a HIGH state. Shorted input fail-safe is not supported
across the common-mode range of the device (V
SS
to
2.4V). It is only supported with inputs shorted and no
external common-mode voltage applied.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 6.0V
-0.3 to (V
DD
+ 0.3V)
-65 to +150°C
1.25 W
+150°C
10°C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage, receiver inputs
DC input voltage, logic inputs
LIMITS
4.5 to 5.5V
-55 to +125°C
2.4V
0 to V
DD
for EN, EN
4
DC ELECTRICAL CHARACTERISTICS
1
(V
DD
= 5.0V +10%; -55°C < T
C
< +125°C)
SYMBOL
V
IH
V
IL
V
OL
V
OH
I
IN
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Logic input leakage current
(TTL)
(TTL)
I
OL
= 2mA, V
DD
= 4.5V
I
OH
= -0.4mA, V
DD
= 4.5V
Inputs, V
IN
= 0 and 2.4V, V
CC
= 5.5
Enables = EN/EN= 0 and 5.5V,
V
CC
= 5.5
V
TH3
V
TL 3
I
I
I
OZ4
V
CL
I
OS 3
I
CC4
I
CCZ 4
Differential Input High Threshold
Differential Input Low Threshold
Receiver input Current
Output Three-State Current
Input clamp voltage
Output Short Circuit Current
Loaded supply current receivers
enabled
Loaded supply current receivers
disabled
V
CM
= +1.2V
V
CM
= +1.2V
V
IN
= 2.4V
Disabled, V
OUT
= 0 V or V
DD
I
CL
= +/-18mA
Enabled, V
OUT
= 0 V
2
EN, EN = V
DD
or V
SS
Inputs Open
EN = V
SS
, EN = V
DD
Inputs Open
mA
11
-100
-10
-10
-1.5
-15
+10
+10
1.5
-130
11
4.0
-10
-10
+10
+10
CONDITION
MIN
2.0
0.8
0.3
MAX
UNIT
V
V
V
V
µA
+100
mV
mV
µΑ
µΑ
V
mA
mA
Notes:
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I
OS
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not excee d
This time, I learned about SmartConfig and Airkiss one-click network configuration, and connected ESP8266 to the cloud with one click.
Generally, if a WiFi module wants to connect to the Internet, the...
Putting assert in a separate article shows how important it is. Raw os provides the RAW_ASSERT interface. It is strongly recommended to enable the assert function during the product development stage....
while (DEF_TRUE) {/* Task body, always written as an infinite loop.*///BSP_LED_Toggle(0);OSTimeDlyHMSM(0, 0, 0, 500); GPIO_SetBits(GPIOE,GPIO_Pin_3); OSTimeDlyHMSM(0, 0, 0, 500); GPIO_ResetBits(GPIOE,...
In the motorWare routine, the module void updateGlobalVariables_motor(CTRL_Handle handle, ST_Handle sthandle) first defines several float parameters in fpu32 and fixed-point mode: In fixed-point mode:...
With the increasing demand for intelligent vehicle assisted driving systems and the development of networking of automotive electronic systems, new reversing radars should be able to continuously meas...
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
Analog Devices held a third-quarter fiscal 2025 earnings conference call. Vincent T. Roche, CEO and Chairman of the Board, and Richard C. Puccio, Executive Vice President and Chief Financial Office...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
introduction
The OMAP-L138 dual-core processor is a new generation of low-power single-chip systems (SoCs) from TI. It is widely used in communications, industrial, medical diagnostic, and aud...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
