DATA SHEET
8GB Registered DDR3 SDRAM DIMM
EBJ82HF4B1RA (1024M words
×
72 bits, 4 Ranks)
Specifications
•
Density: 8GB
•
Organization
1024M words
×
72 bits, 4 ranks
•
Mounting 36 pieces of 2G bits DDR3 SDRAM with
DDP (FBGA)
DDP: 2 pieces of 1G bits chips sealed in one
package
•
Package: 240-pin socket type dual in line memory
module (DIMM)
PCB height: 30.5mm (max.)
Lead pitch: 1.0mm
Lead-free (RoHS compliant)
•
Power supply: VDD
=
1.5V
±
0.075V
•
Data rate: 1066Mbps/800Mbps (max.)
•
Eight internal banks for concurrent operation
(components)
•
Interface: SSTL_15
•
Burst lengths (BL): 8 and 4 with Burst Chop (BC)
•
/CAS Latency (CL): 6, 7, 8
•
/CAS write latency (CWL): 5, 6
•
Precharge: auto precharge option for each burst
access
•
Refresh: auto-refresh, self-refresh
•
Refresh cycles
Average refresh period
7.8µs at 0°C
≤
TC
≤ +85°C
3.9µs at
+85°C <
TC
≤ +95°C
•
Operating case temperature range
TC = 0°C to +95°C
Features
•
Double-data-rate architecture; two data transfers per
clock cycle
•
The high-speed data transfer is realized by the 8 bits
prefetch pipelined architecture
•
Bi-directional differential data strobe (DQS and /DQS)
is transmitted/received with data for capturing data at
the receiver
•
DQS is edge-aligned with data for READs; center-
aligned with data for WRITEs
•
Differential clock inputs (CK and /CK)
•
DLL aligns DQ and DQS transitions with CK
transitions
•
Commands entered on each positive CK edge; data
and data mask referenced to both edges of DQS
•
Posted /CAS by programmable additive latency for
better command and data bus efficiency
•
On-Die-Termination (ODT) for better signal quality
Synchronous ODT
Dynamic ODT
Asynchronous ODT
•
Multi Purpose Register (MPR) for temperature read
out
•
ZQ calibration for DQ drive and ODT
•
Programmable Partial Array Self-Refresh (PASR)
•
/RESET pin for Power-up sequence and reset
function
•
SRT range:
Normal/extended
Auto/manual self-refresh
•
Programmable Output driver impedance control
•
2 piece of registering clock driver and 1 piece of
serial EEPROM (256 bytes EEPROM) for Presence
Detect (PD)
•
Class B temperature sensor functionality with
EEPROM
Note: Warranty void if removed DIMM heat
spreader.
Document No. E1306E30 (Ver. 3.0)
Date Published December 2008 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida
Memory, Inc. 2008
EBJ82HF4B1RA
Pin Description
Pin name
A0 to A15
A10 (AP)
A12 (/BC)
BA0, BA1, BA2
DQ0 to DQ63
CB0 to CB7
/RAS
/CAS
/WE
/CS0, /CS1, /CS2, /CS3
CKE0, CKE1
CK0, CK1
/CK0, /CK1
DQS0 to DQS17, /DQS0 to /DQS17
SCL
SDA
SA0, SA1, SA2
VDD
VDDSPD
VREFCA
VREFDQ
VSS
VTT
/RESET
ODT0, ODT1
Par_In
/Err_Out
/Event
NC
Function
Address input
Row address
Column address
Auto precharge
Burst chop
Bank select address
Data input/output
Check bit (Data input/output)
Row address strobe command
Column address strobe command
Write enable
Chip select
Clock enable
Clock input
Differential clock input
Input and output data strobe
Clock input for serial PD
Data input/output for serial PD
Serial address input
Power for internal circuit
Power for serial EEPROM
Reference voltage for CA
Reference voltage for DQ
Ground
Termination Voltage
Set DRAM to known state
ODT control
Parity bit for the Address and Control bus
Parity error found on the Address and Control bus
Temperature event pin
No connection
A0 to A13
A0 to A9, A11
Data Sheet E1306E30 (Ver. 3.0)
5
京公网安备 11010802033920号
EEWORLD
