Operational environment: total dose irradiation testing to MIL-
STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1Mrad(Si)
- Latchup immune (LET > 100 MeV-cm
2
/mg)
Packaging options:
- 16-lead flatpack (0.7 grams)
Standard Microcircuit Drawing 5962-95834
- QML Q and V compliant part
Compatible with IEEE 1596.3SCI LVDS
Compatible with ANSI/TIA/EIA 644-1996 LVDS Standard
INTRODUCTION
The UT54LVDS032 Quad Receiver is a quad CMOS differential
line receiver designed for applications requiring ultra low power
dissipation and high data rates. The device is designed to support
data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low
Voltage Differential Signaling (LVDS) technology.
The UT54LVDS032 accepts low voltage (340mV) differential
input signals and translates them to 5V TTL output levels. The
receiver supports a three-state function that may be used to
multiplex outputs. The receiver also supports OPEN, shorted and
terminated (100) input fail-safe. Receiver output will be HIGH
for all fail-safe conditions.
The UT54LVDS032 and companion quad line driver
UT54LVDS031 provide new alternatives to high power pseudo-
ECL devices for high speed point-to-point interface applications.
R
IN1+
R
IN1-
+
R1
-
R
OUT1
R
IN2+
R
IN2-
+
R2
-
R
OUT2
R
IN3+
R
IN3-
+
R3
-
R
OUT3
R
IN4+
R
IN4-
EN
EN
+
R4
-
R
OUT4
Figure 1. UT54LVDS032 Quad Receiver Block Diagram
36-00-06-001
Version 1.0.1
1
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
APPLICATIONS INFORMATION
The UT54LVDS032 receiver’s intended use is primarily in an
uncomplicated point-to-point configuration as is shown in Figure
3. This configuration provides a clean signaling environment for
quick edge rates of the drivers. The receiver is connected to the
driver through a balanced media which may be a standard twisted
pair cable, a parallel pair cable, or simply PCB traces. Typically,
the characteristic impedance of the media is in the range of 100.
A termination resistor of 100should be selected to match the
media and is located as close to the receiver input pins as possible.
The termination resistor converts the current sourced by the driver
into voltages that are detected by the receiver. Other configurations
are possible such as a multi-receiver configuration, but the effects
of a mid-stream connector(s), cable stub(s), and other impedance
discontinuities, as well as ground shifting, noise margin limits, and
total termination loading must be taken into account.
R
IN1-
R
IN1+
R
OUT1
EN
R
OUT2
R
IN2+
R
IN2-
V
SS
1
2
3
4
5
6
7
8
UT54LVDS032
Receiver
16
15
14
13
12
11
10
9
V
DD
R
IN4-
R
IN4+
R
OUT4
EN
R
OUT3
R
IN3+
R
IN3-
Figure 2. UT54LVDS032 Pinout
ENABLE
TRUTH TABLE
Enables
EN
L
EN
H
Input
R
IN+
- R
IN
-
X
V
ID
> 0.1V
V
ID
< -0.1V
Full Fail-safe
OPEN/SHORT or
Terminated
PIN DESCRIPTION
Pin No.
2, 6, 10, 14
1, 7, 9, 15
3, 5, 11, 13
4
12
16
8
Name
R
IN+
R
IN-
R
OUT
EN
EN
V
DD
V
SS
Description
Non-inverting receiver input pin
Inverting receiver input pin
Receiver output pin
Active high enable pin, OR-ed
with EN
Active low enable pin, OR-ed
with EN
Power supply pin, +5V + 10%
Ground pin
Output
R
OUT
Z
H
L
H
DATA
INPUT
1/4 UT54LVDS031
RT 100
1/4 UT54LVDS032
+
-
DATA
OUTPUT
Figure 3. Point-to-Point Application
All other combinations
of ENABLE inputs
The UT54LVDS032 differential line receiver is capable of
detecting signals as low as 100mV, over a + 1V common-mode
range centered around +1.2V. This is related to the driver offset
voltage which is typically +1.2V. The driven signal is centered
around this voltage and may shift +1V around this center point.
The +1V shifting may be the result of a ground potential difference
between the driver’s ground reference and the receiver’s ground
reference, the common-mode effects of coupled noise or a
combination of the two. Both receiver input pins should honor their
specified operating input voltage range of 0V to +2.4V (measured
from each pin to ground).
36-00-06-001
Version 1.0.1
2
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
Receiver Fail-Safe
The UT54LVDS032 receiver is a high gain, high speed device that
amplifies a small differential signal (20mV) to TTL logic levels.
Due to the high gain and tight threshold of the receiver, care should
be taken to prevent noise from appearing as a valid signal.
The receiver’s internal fail-safe circuitry is designed to source/sink
a small amount of current, providing fail-safe protection (a stable
known state of HIGH output voltage) for floating, terminated or
shorted receiver inputs.
1.
Open Input Pins.
The UT54LVDS032 is a quad receiver
device, and if an application requires only 1, 2 or 3
receivers, the unused channel(s) inputs should be left
OPEN. Do not tie unused receiver inputs to ground or any
other voltages. The input is biased by internal high value
pull up and pull down resistors to set the output to a HIGH
state. This internal circuitry will guarantee a HIGH, stable
output state for open inputs.
2.
Terminated Input.
If the driver is disconnected (cable
unplugged), or if the driver is in a three-state condition, the
receiver output will again be in a HIGH state, even with the
end of cable 100 termination resistor across the input pins.
The unplugged cable can become a floating antenna which
can pick up noise. If the cable picks up more than 10mV of
differential noise, the receiver may see the noise as a valid
signal and switch. To insure that any noise is seen as
common-mode and not differential, a balanced
interconnect should be used. Twisted pair cable offers better
balance than flat ribbon cable.
3.
Shorted Inputs.
If a fault condition occurs that shorts the
receiver inputs together, thus resulting in a 0V differential
input voltage, the receiver output remains in a HIGH state.
Shorted input fail-safe is not supported across the common-
mode range of the device (V
SS
to 2.4V). It is only supported
with inputs shorted and no external common-mode voltage
applied.
36-00-06-001
Version 1.0.1
3
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
OPERATIONAL ENVIRONMENT
PARAMETER
Total Ionizing Dose (TID)
Single Event Latchup (SEL)
Neutron Fluence
1
Notes:
1. Guarnteed but not tested.
LIMIT
1.0E6
>100
1.0E13
UNITS
rad(Si)
MeV-cm
2
/mg
n/cm
2
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 6.0V
-0.3 to (V
DD
+ 0.3V)
-65 to +150C
1.25 W
+150C
10C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage, receiver inputs
DC input voltage, logic inputs
LIMITS
4.5 to 5.5V
-55 to +125C
2.4V
0 to V
DD
for EN, EN
36-00-06-001
Version 1.0.1
4
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
DC ELECTRICAL CHARACTERISTICS *
1
SYMBOL
V
IH
V
IL
V
OL
V
OH
I
IN
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Logic input leakage current
(TTL)
(TTL)
(V
DD
= 5.0V +10%; -55C < T
C
< +125C); Unless otherwise
CONDITION
MIN
2.0
0.8
0.3
4.0
-10
-10
+10
+10
MAX
UNIT
V
V
V
V
A
I
OL
= 2mA, V
DD
= 4.5V
I
OH
= -0.4mA, V
DD
= 4.5V
Inputs, V
IN
= 0 and 2.4V, V
CC
= 5.5
Enables = EN/EN= 0 and 5.5V,
V
CC
= 5.5
V
CM
= +1.2V
V
CM
= +1.2V
V
IN
= 2.4V
Disabled, V
OUT
= 0 V or V
DD
I
CL
= +/-18mA
Enabled, V
OUT
= 0 V
2
EN, EN = V
DD
or V
SS
Inputs Open
EN = V
SS
, EN = V
DD
Inputs Open
-100
-10
-10
-1.5
-15
V
TH3
V
TL3
I
I
I
OZ4
V
CL
I
OS3
I
CC4
I
CCZ4
Differential Input High Threshold
Differential Input Low Threshold
Receiver input Current
Output Three-State Current
Input clamp voltage
Output Short Circuit Current
Loaded supply current receivers
enabled
Loaded supply current receivers
disabled
+100
mV
mV
+10
+10
1.5
-130
11
V
mA
mA
mA
11
noted, Tc is per the temperature range ordered
Notes:
* For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25
o
C per MIL-STD-883 Method 1019, Condition
A up to the maximum TID level procured.
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I
OS
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum
Today I received a request from a client to help me with a few questions. Please help me, thank you!!! I. Drawing explanation 1. Use the circuit to explain that the same address can be input into the ...
I have been working on the ADC1 of STM8S105 for the past few days and I am very depressed. Now let me tell you the problem:
Manually starting ADC1 and reading ADC1 are both normal;
However, now I want...
Emerging W-CDMA applications with high-speed data connections (HSDPA) present some unique power requirements compared to previous generations. To achieve maximum data rates, the RF PA requires a nomin...
[i=s]This post was last edited by starsdu on 2020-6-11 19:14[/i]I have a question. DSP TMS320C6748 is a 32-bit processor of C6000. The address bus is 32 bits, and the data bus should also correspond t...
[size=5]Enter CCS Debug mode, click the small arrow on the right side of the debug button to open the drop-down list, select Debug Configurations, and select Realtime Options->Halt the target before a...
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
Is pure electric vehicles a false proposition for long-distance driving? At least from my personal perspective, based on current technological and infrastructure standards, I believe so. Below, I'l...[Details]
Topics: Bring Your Own Device (BYOD) trends; the impact of using employees' own mobile devices to control access to work facilities and equipment on information security; and ways to securely imple...[Details]
White light LEDs are voltage-sensitive devices. In actual operation, their upper limit is 20mA. However, the current often increases due to various reasons during use. If no protective measures are...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
The Automotive Testing and Quality Assurance Expo (ATE 2025) will open on August 27th. At the expo, Rohde & Schwarz (R&S) will showcase six automotive testing solutions, themed "Intelligently Drivi...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
Coal mines typically contain gas and coal dust. When gas and coal dust reach a certain concentration, they can cause explosions. Electrical equipment generates arcs during normal operation or durin...[Details]
Chinese characters are extensive and profound, and there are many different names for ESD tubes. How many of them do you know?
As far as I know, ESD diodes are currently known as ESD p...[Details]
Bosch has released a new SoC series to support L2+ advanced driver assistance functions. The chip integrates high resolution and long-range detection capabilities, and has built-in support for neur...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]
The driving mode is not unfamiliar to vehicles. According to the driving mode of the vehicle, there are front-wheel drive, rear-wheel drive and even four-wheel drive. Four-wheel drive is a major se...[Details]
With the growth of the Internet of Things (IoT), wearable, and portable devices, consumers are growing weary of cluttered cables and the need for frequent battery recharges. The benefits of wireles...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
