EEWORLDEEWORLDEEWORLD

Part Number

Search

50579-5123H

Description
Board Connector, 123 Contact(s), 3 Row(s), Female, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Plug
CategoryThe connector    The connector   
File Size301KB,4 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

50579-5123H Overview

Board Connector, 123 Contact(s), 3 Row(s), Female, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Plug

50579-5123H Parametric

Parameter NameAttribute value
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresOPTIONAL POLARIZATION
Board mount optionsHOLE .099-.111
body width0.336 inch
subject depth0.72 inch
body length4.85 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON PD-NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYPHENYLENE SULPHIDE
Manufacturer's serial number50579
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number3
Number of rows loaded3
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thicknessFLASH inch
polarization keyPOLARIZED KEY
Rated current (signal)1 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.18 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts123
Base Number Matches1
Suddenly thought of the message mailbox
Suppose there are two tasks task1(); task2();Task1 has a higher priority than task2. The specific examples are as follows:Under normal circumstances, if A puts the received data message into the mailb...
ciniao300 Embedded System
Is it better for the crystal oscillator trace to transition from thick to thin to the chip or to keep it the same width as the chip pins?
As the title says! I hope an expert can give a theoretical answer. Thank you! Is it better to make the crystal trace as thick as possible or to keep it consistent? If it is consistent, it cannot be to...
shenlan0302 PCB Design
USB HID experimental doubts about LPC1343
When I was learning the USB HID experiment of LPC1343, I found that the received data was EP0Buf[0]=0x01, which is the data I sent and received, but EP0Buf[1]=0x81, EP0Buf[2=0x7F, I don't know what th...
wanda216 NXP MCU
What products can planar transformers be used in?
What products can planar transformers be used in?...
c709244459 Discrete Device
[Show samples] + Sharing experience on TI sample application
[i=s]This post was last edited by tagetage on 2015-8-3 14:52[/i] I have been using TI chip companies, mainly using MSP430 MCUs. I have always felt very good about TI chips. The chips have high perform...
tagetage TI Technology Forum
The problem of converting 0~5V to 0~3.3V
The pressure sensor used in the project is a differential signal, and I use an instrument amplifier to convert it into a 0~5V signal. However, the microcontroller is STM32F767, and the AD can only rec...
chenbingjy stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2382  2464  716  2299  2611  48  50  15  47  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号