Radiation-hardened design; total dose irradiation testing to
MIL-STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1Mrad(Si)
- Latchup immune (LET > 100 MeV-cm
2
/mg)
Packaging options:
- 16-lead flatpack (dual in-line)
Standard Microcircuit Drawing 5962-95834
- QML Q and V compliant part
Compatible with IEEE 1596.3SCI LVDS
Compatible with ANSI/TIA/EIA 644-1996 LVDS Standard
INTRODUCTION
The UT54LVDS032 Quad Receiver is a quad CMOS differential
line receiver designed for applications requiring ultra low power
dissipation and high data rates. The device is designed to support
data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low
Voltage Differential Signaling (LVDS) technology.
The UT54LVDS032 accepts low voltage (340mV) differential
input signals and translates them to 5V TTL output levels. The
receiver supports a three-state function that may be used to
multiplex outputs. The receiver also supports OPEN, shorted
and terminated (100
Ω)
input fail-safe. Receiver output will be
HIGH for all fail-safe conditions.
The UT54LVDS032 and companion quad line driver
UT54LVDS031 provides new alternatives to high power
pseudo-ECL devices for high speed point-to-point interface
applications.
R
IN1+
R
IN1-
R
IN2+
R
IN2-
R
IN3+
R
IN3-
R
IN4+
R
IN4-
EN
EN
+
R1
-
R
OUT1
+
R2
-
R
OUT2
+
R3
-
R
OUT3
+
R4
-
R
OUT4
Figure 1. UT54LVDS032 Quad Receiver Block Diagram
1
APPLICATIONS INFORMATION
The UT54LVDS032 receiver’s intended use is primarily in an
uncomplicated point-to-point configuration as is shown in
Figure 3. This configuration provides a clean signaling
environment for quick edge rates of the drivers. The receiver is
connected to the driver through a balanced media which may be
a standard twisted pair cable, a parallel pair cable, or simply
PCB traces. Typically, the characteristic impedance of the media
is in the range of 100Ω. A termination resistor of 100Ω should
be selected to match the media and is located as close to the
receiver input pins as possible. The termination resistor converts
the current sourced by the driver into voltages that are detected
by the receiver. Other configurations are possible such as a
multi-receiver configuration, but the effects of a mid-stream
connector(s), cable stub(s), and other impedance discontinuities,
as well as ground shifting, noise margin limits, and total
termination loading must be taken into account.
R
IN1-
R
IN1+
R
OUT1
EN
R
OUT2
R
IN2+
R
IN2-
V
SS
1
2
3
4
5
6
7
8
UT54LVDS032
Receiver
16
15
14
13
12
11
10
9
V
DD
R
IN4-
R
IN4+
R
OUT4
EN
R
OUT3
R
IN3+
R
IN3-
Figure 2. UT54LVDS032 Pinout
TRUTH TABLE
Enables
EN
L
EN
H
Input
R
IN+
- R
IN
-
X
V
ID
> 0.1V
V
ID
< -0.1V
Full Fail-safe
OPEN/SHORT or
Terminated
PIN DESCRIPTION
Pin No.
2, 6, 10, 14
1, 7, 9, 15
3, 5, 11, 13
4
12
16
8
Name
R
IN+
R
IN-
R
OUT
EN
EN
V
DD
V
SS
Description
Non-inverting receiver input pin
Inverting receiver input pin
Receiver output pin
Active high enable pin, OR-ed
with EN
Active low enable pin, OR-ed
with EN
Power supply pin, +5V + 10%
Ground pin
Output
R
OUT
Z
H
L
H
DATA
INPUT
ENABLE
1/4 UT54LVDS032
RT 100Ω
+
-
DATA
OUTPUT
1/4 UT54LVDS031
All other combinations
of ENABLE inputs
Figure 3. Point-to-Point Application
The UT54LVDS032 differential line receiver is capable of
detecting signals as low as 100mV, over a + 1V common-mode
range centered around +1.2V. This is related to the driver offset
voltage which is typically +1.2V. The driven signal is centered
around this voltage and may shift +1V around this center point.
The +1V shifting may be the result of a ground potential
difference between the driver’s ground reference and the
receiver’s ground reference, the common-mode effects of
coupled noise or a combination of the two. Both receiver input
pins should honor their specified operating input voltage range
of 0V to +2.4V (measured from each pin to ground).
2
Receiver Fail-Safe
The UT54LVDS032 receiver is a high gain, high speed device
that amplifies a small differential signal (20mV) to TTL logic
levels. Due to the high gain and tight threshold of the receiver,
care should be taken to prevent noise from appearing as a valid
signal.
The receiver’s internal fail-safe circuitry is designed to source/
sink a small amount of current, providing fail-safe protection (a
stable known state of HIGH output voltage) for floating,
terminated or shorted receiver inputs.
1.
Open Input Pins.
The UT54LVDS032 is a quad
receiver device, and if an application requires only 1, 2
or 3 receivers, the unused channel(s) inputs should be
left OPEN. Do not tie unused receiver inputs to ground
or any other voltages. The input is biased by internal high
value pull up and pull down resistors to set the output to
a HIGH state. This internal circuitry will guarantee a
HIGH, stable output state for open inputs.
2.
Terminated Input.
If the driver is disconnected (cable
unplugged), or if the driver is in a three-state condition,
the receiver output will again be in a HIGH state, even
with the end of cable 100Ω termination resistor across
the input pins. The unplugged cable can become a
floating antenna which can pick up noise. If the cable
picks up more than 10mV of differential noise, the
receiver may see the noise as a valid signal and switch.
To insure that any noise is seen as common-mode and
not differential, a balanced interconnect should be used.
Twisted pair cable offers better balance than flat ribbon
cable.
3.
Shorted Inputs.
If a fault condition occurs that shorts
the receiver inputs together, thus resulting in a 0V
differential input voltage, the receiver output remains in
a HIGH state. Shorted input fail-safe is not supported
across the common-mode range of the device (V
SS
to
2.4V). It is only supported with inputs shorted and no
external common-mode voltage applied.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 6.0V
-0.3 to (V
DD
+ 0.3V)
-65 to +150°C
1.25 W
+150°C
10°C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage, receiver inputs
DC input voltage, logic inputs
LIMITS
4.5 to 5.5V
-55 to +125°C
2.4V
0 to V
DD
for EN, EN
4
DC ELECTRICAL CHARACTERISTICS
1
(V
DD
= 5.0V +10%; -55°C < T
C
< +125°C)
SYMBOL
V
IH
V
IL
V
OL
V
OH
I
IN
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Logic input leakage current
(TTL)
(TTL)
I
OL
= 2mA, V
DD
= 4.5V
I
OH
= -0.4mA, V
DD
= 4.5V
Inputs, V
IN
= 0 and 2.4V, V
CC
= 5.5
Enables = EN/EN= 0 and 5.5V,
V
CC
= 5.5
V
TH3
V
TL 3
I
I
I
OZ4
V
CL
I
OS 3
I
CC4
I
CCZ 4
Differential Input High Threshold
Differential Input Low Threshold
Receiver input Current
Output Three-State Current
Input clamp voltage
Output Short Circuit Current
Loaded supply current receivers
enabled
Loaded supply current receivers
disabled
V
CM
= +1.2V
V
CM
= +1.2V
V
IN
= 2.4V
Disabled, V
OUT
= 0 V or V
DD
I
CL
= +/-18mA
Enabled, V
OUT
= 0 V
2
EN, EN = V
DD
or V
SS
Inputs Open
EN = V
SS
, EN = V
DD
Inputs Open
mA
11
-100
-10
-10
-1.5
-15
+10
+10
1.5
-130
11
4.0
-10
-10
+10
+10
CONDITION
MIN
2.0
0.8
0.3
MAX
UNIT
V
V
V
V
µA
+100
mV
mV
µΑ
µΑ
V
mA
mA
Notes:
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I
OS
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not excee d
How to design a protection circuit to protect the SCL and SDA signals of the I2C adapter? Sometimes, 12V DC is accidentally injected directly into the SCL signal of the I2C adapter, causing the entire...
[i=s]This post was last edited by DavidZH on 2015-12-27 20:21[/i] At present, the object tracking effect has been realized. The video shows the tracking of different coins. The core idea of tracking i...
Welcome everyone to practice together: https://bbs.eeworld.com.cn/thread-1154979-1-1.htmlThe following is a summary of the practice posts:username
Share Link@ tomjianchun.xu" Practice Together in 2021...
In uCOS II, I use uCOS to write a program for LM3S6911. All three serial ports receive or send serial port data in query mode! When I create tasks in the main function and put the three separate seria...
I am new to using the SMC1602A display and I have encountered some problems that I don't know how to solve, such as cursor control. If I want it to be displayed at a specified position, how should I w...
I have used matlab to generate a data file .DAT. Apart from the format 1651 4 0 0 0 at the beginning of the file, are there any requirements for the data itself?After using fopen, I used fscanf to rea...
On August 24th, Tesla CEO Elon
Musk
revealed information about the upcoming FSD V14, claiming it will outperform human drivers. Tesla FSD lead Ashok stated last year that FSD version 12.5, ...[Details]
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
1. Ease of Use: The HMI module should be designed to be simple and clear, allowing users to easily operate and configure the energy storage device.
2. Ease of Maintenance: The HMI module should...[Details]
On August 22, according to CNBC's report today, the National Highway Traffic Safety Administration (NHTSA) is launching an investigation into Tesla, and the latter is questioned whether it has fail...[Details]
China, August 21, 2025 – STMicroelectronics (NYSE: STM), a world-leading semiconductor company serving a wide range of electronics applications, has published its IFRS 2025 semi-annual financial re...[Details]
Shenzhen Baowei Power Supply high frequency pure sine wave power, communication inverter power supply has two communication interfaces, RS232 and R485 interfaces, their functions and characteristic...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
With growing environmental awareness, the continuous improvement of three-electric technology and the increasing deployment of infrastructure such as charging stations, the electrification of new e...[Details]
On August 21, according to a report by Korean media SEDaily yesterday, according to semiconductor industry sources, the HBM4 samples provided by Samsung to Nvidia last month have passed initial tes...[Details]
I recently read an article in the Wall Street Journal titled "We need the right to repair our gadgets" (reference original article: ). The author was very angry about the phenomenon of "planned obs...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
