NOTICE OF REVISION (NOR)
(See MIL-STD-480 for instructions)
This revision described below has been authorized for the document listed.
DATE (YYMMDD)
91-11-06
Form Approved
OMB No. 0704-0188
Public reporting burden for this collection is estimated to average 1 hour per response, including the time for reviewing instructions, searching
existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments
regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to
Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington,
VA 22202-4302, and to the Office of Information and Regulatory Affairs, Office of Management and Budget, Washington, DC 20503.
1. ORIGINATOR NAME AND ADDRESS
Defense Electronics Supply Center
Dayton, Ohio 45444-5277
2. CAGE CODE
67268
4. CAGE CODE
67268
6. TITLE OF DOCUMENT
MICROCIRCUIT, DIGITAL, LOW POWER, SINGLE CHANNEL, DRIVER-RECEIVER,
HYBRID
7. REVISION LETTER
(Current) A
8. ECP NO.
(New) B
3. NOR NO.
5962-R034-92
5. DOCUMENT NO.
5962-89592
9. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES
ALL
10. DESCRIPTION OF REVISION
Sheet 1: Revisions ltr column; add "B"
Revisions description column; add "Changes in accordance with
NOR 5962-R034-92".
Revisions date column; add "91-11-06".
Sheet 7: Table I, Add subgroup 5 to the I
CC
-100 and I
EE
-100 tests and remove the temperature reference in the
conditions block for these tests.
11. THIS SECTION FOR GOVERNMENT USE ONLY
a. CHECK ONE
A
X
B
EXISTING DOCUMENT SUPPLEMENTED
BY THIS NOR MAY BE USED IN
MANUFACTURE.
b. ACTIVITY AUTHORIZED TO APPROVE
CHANGE FOR GOVERNMENT
DESC-ECT
12. ACTIVITY ACCOMPLISHING REVISION
DESC-ECT
DD Form 1695, JUL 88
A B
REVISED DOCUMENT MUST BE
RECEIVED BEFORE MANUFACTURER
MAY INCORPORATE THIS CHANGE.
A B
CUSTODIAN OF MASTER DOCUMENT
SHALL MAKE ABOVE REVISION AND
FURNISH REVISED DOCUMENT TO:
SIGNATURE AND TITLE
Greg Lude
Branch Chief
DATE (YYMMDD)
91-11-06
REVISION COMPLETED (Signature)
DATE (YYMMDD)
Shelly M. Jenkins
91-11-06
Previous editions are obsolete.
REVISIONS
LTR
A
DESCRIPTION
Add device types 05 and 06. Correct coupling diagram, figure 4. Add
common mode input voltage and test circuit. Table I, change ISIH.
Editorial changes throughout.
DATE
(YR-MO-DA)
91-05-17
APPROVED
W. Heckman
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
A
15
A
16
REV
SHEET
PMIC N/A
A
1
A
2
A
3
A
4
A
5
A
6
A
7
8
9
A
10
A
11
A
12
A
13
A
14
PREPARED BY
Donald R. Osborne
CHECKED BY
RAY MONNIN
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
20 JUNE 1989
REVISION LEVEL
A
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
STANDARDIZED
MILITARY
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
MICROCIRCUIT, DIGITAL, LOW POWER, SINGLE
CHANNEL, DRIVER-RECEIVER, HYBRID
SIZE
CAGE CODE
A
SHEET
67268
1
5962-89592
OF
16
1987--748-129/60912
DESC FORM 193
SEP 87
DISTRIBUTION STATEMENT A.
* US GOVERNMENT PRINTING OFFICE:
5962-E093
Approved for public release; distribution is unlimited.
1. SCOPE
1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with
MIL-H-38534.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example:
5962-89592
01
X
X
Drawing number
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish per
MIL-H-38534
1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
01 and 03
02 and 04
05
06
Generic number
ARX3407
ARX3404
ARX3467
ARX3464
Circuit function
Single channel, driver-receiver (MIL-STD-1553 A and B) low power,
receiver standby high
Single channel, driver-receiver (universal transceiver) low power, receiver
standby high
Single channel, driver-receiver (MIL-STD-1553 A and B) low power,
receiver standby low
Single channel, driver-receiver (universal transceiver) low power, receiver
standby low
1.2.2 Case outline(s). The case outline(s) shall be as designated in appendix C of MIL-M-38510,
and as follows:
Outline letter
X
Y
1.3 Absolute maximum ratings.
Supply voltage:
V
CC
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
V
EE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+5 V supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Logic input voltage range - - - - - - - - - - - - - - - - - - - - - - - -
Receiver differential input voltage - - - - - - - - - - - - - - - - - - -
Receiver common mode input voltage range - - - - - - - - - -
Driver peak output current - - - - - - - - - - - - - - - - - - - - - - -
Storage temperature range - - - - - - - - - - - - - - - - - - - - - - -
Lead temperature (soldering, 10 seconds) - - - - - - - - - - - -
Junction temperature (T
J
) - - - - - - - - - - - - - - - - - - - - - - - -
Power dissipation (P
D
) total hybrid:
100 percent duty cycle (T
C
= +25
C):
Device types 01, 03, and 05 - - - - - - - - - - - - - - - - - - - -
Device types 02, 04, and 06 - - - - - - - - - - - - - - - - - - - -
Standby mode, all devices - - - - - - - - - - - - - - - - - - - - - - -
Case outline
See figure 1 (24-lead, 1.27" x 1.27" x .175"), hybrid package
See figure 1 (24-lead, 1.27" x 1.27" x .200"), flat package
-0.3 V dc to +18 V dc
+0.3 V dc to -18 V dc
-0.3 V dc to +7 V dc
-0.3 V to +5.5 V
40 Vp-p
-10 V to +10 V
±300 mA
-65
C to +150
C
+300
C
+160
C
3.0 W
3.24 W
1.06 W
SIZE
STANDARDIZED
A
REVISION LEVEL
A
5962-89592
SHEET
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
DESC FORM 193A
SEP 87
2
Power dissipation (P
D
) hottest die:
100 percent duty cycle:
Device types 01, 03, and 05 - - - - - - - - - - - - - - - - - - - - -
Device types 02, 04, and 06 - - - - - - - - - - - - - - - - - - - - -
Standby mode, all devices - - - - - - - - - - - - - - - - - - - - - - -
Thermal resistance:
Junction-to-case (O
JC
) hottest die:
Device types 01, 02, 05, and 06 - - - - - - - - - - - - - - - - - -
Device types 03 and 04 - - - - - - - - - - - - - - - - - - - - - - - -
Case-to-ambient, all devices - - - - - - - - - - - - - - - - - - - - -
Maximum junction-to-case temperature rise for the
hottest die at 100 percent duty cycle:
Device types 01 and 05 - - - - - - - - - - - - - - - - - - - - - - - -
Device types 02 and 06 - - - - - - - - - - - - - - - - - - - - - - -
Device type 03 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Device type 04 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1.4 Recommended operating conditions.
Supply voltage range:
V
CC
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
V
EE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
5 V supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Logic input voltage range - - - - - - - - - - - - - - - - - - - - - - - -
Receiver differential voltage - - - - - - - - - - - - - - - - - - - - - - -
Receiver common mode voltage range - - - - - - - - - - - - - -
Driver peak output current:
Device types 01, 02, 05, and 06 - - - - - - - - - - - - - - - - - -
Device types 03 and 04 - - - - - - - - - - - - - - - - - - - - - - - -
Maximum serial data rate - - - - - - - - - - - - - - - - - - - - - - - -
Case operating temperature range (T
C
) - - - - - - - - - - - - - -
484 mW 1/ 2/
545 mW 2/ 3/
Derates to zero
88
C/W
58
C/W
21
C/W
42.6
C
47.9
C
+28
C
31.6
C
+11.4 V dc to +15.75 V dc
-11.4 V dc to -15.75 V dc
+4.5 V dc to +5.5 V dc
0 V to +5.0 V
40 Vp-p
-10.0 V to +10.0 V
±180 mA
±120 mA
1.0 MHz
-55
C to +125
C
1/
2/
3/
Duty cycle at 1.0 MHz for device types 01 and 05. Derate to 82 percent maximum at T
C
= +125
C for a maximum junction
temperature of +160
C in the hottest die.
Duty cycle for device types 03 and 04 needs no derating over the full operating temperature range.
Duty cycle at 1.0 MHz for device types 02 and 06. Derate to 73 percent maximum at T
C
= +125
C for a maximum junction
temperature of +160
C in the hottest die.
SIZE
STANDARDIZED
A
REVISION LEVEL
A
5962-89592
SHEET
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
DESC FORM 193A
SEP 87
3
2. APPLICABLE DOCUMENTS
2.1 Government specifications and standard. Unless otherwise specified, the following specifications and standard of the issue
listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of
this drawing to the extent specified herein.
SPECIFICATIONS
MILITARY
MIL-M-38510
MIL-H-38534
STANDARD
MILITARY
MIL-STD-883
- Test Methods and Procedures for Microelectronics.
- Microcircuits, General Specification for.
- Hybrid Microcircuits, General Specification for.
(Copies of the specifications and standard required by manufacturers in connection with specific
acquisition functions should be obtained from the contracting activity or as directed by the
contracting activity.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing shall take precedence.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-H-38534
and as specified herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical
dimensions shall be as specified in MIL-H-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests
for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-H-38534. The part shall be marked with the PIN listed in 1.2 herein. In
addition, the manufacturer's PIN may also be marked as listed in QML-38534 (see 6.6 herein).
3.6 Manufacturer eligibility. In addition to the general requirements of MIL-H-38534, the manufacturer of the part described
herein shall submit for DESC-ECC review and approval electrical test data (variables format) on 22 devices from the initial quality
conformance inspection group A lot sample, produced on the certified line, for each device type listed herein. The data should also
include a summary of all parameters manually tested, and for those which, if any, are guaranteed.
SIZE
STANDARDIZED
A
REVISION LEVEL
A
5962-89592
SHEET
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
DESC FORM 193A
SEP 87
4
Analog electronics
京公网安备 11010802033920号
EEWORLD
