EEWORLDEEWORLDEEWORLD

Part Number

Search

RC55C-20KFI

Description
RESISTOR, METAL FILM, 0.25W, 1%, 50ppm, 20000ohm, THROUGH HOLE MOUNT, AXIAL LEADED, LEAD FREE
CategoryPassive components    The resistor   
File Size448KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

RC55C-20KFI Overview

RESISTOR, METAL FILM, 0.25W, 1%, 50ppm, 20000ohm, THROUGH HOLE MOUNT, AXIAL LEADED, LEAD FREE

RC55C-20KFI Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTT Electronics plc
package instructionAxial,
Reach Compliance Codecompliant
Other featuresPRECISION
structureEpoxy Coating
JESD-609 codee3
Lead diameter0.6 mm
Manufacturer's serial numberRC
Installation featuresTHROUGH HOLE MOUNT
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package diameter2.5 mm
Package length7.2 mm
Package shapeTUBULAR PACKAGE
Package formAxial
method of packingAMMO PACK
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance20000 Ω
Resistor typeFIXED RESISTOR
seriesRC
surface mountNO
technologyMETAL FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin (Sn) - hot dipped
Terminal shapeWIRE
Tolerance1%
Operating Voltage350 V
Base Number Matches1
Precision Metal
Film Resistors
RC series
CECC released products with low
TCRs over a wide resistance range
Resistance tolerance down to 0.05%
Express delivery available
Low noise and negligible voltage coefficient
Screened parts available for critical
applications
Electrical Data
RC55
Commercial
Power rating at 70°C
Resistance range
Limiting element voltage
Isolation voltage
TCR (20 to +70°C) & codes
Resistance tolerance
CECC 40101-004 Requirements
Power rating at 70°C
Resistance range
Limiting element voltage
Isolation voltage
TCR & codes
Resistance tolerance (code)
CECC 40101-804 Requirements
Power rating at 70°C
Resistance range
Limiting element voltage
Isolation voltage
TCR & codes
Resistance tolerance (code)
watts
ohms
volts
volts
ppm/°C
%
watts
volts
volts
ppm/°C
%
A
0.125
1R to 1M
200
280
B
0.25
1R to 1M
250
350
watts
ohm
volts
volts
ppm/°C
%
H
0.063
200
280
J
0.125
200
280
0.25
1R to 4M
350
500
0.5
1R to 4M
350
500
5(V), 10(T), 15(Y), 25(D), 50(C), 100(Z)
0.05(W), 0.1(B), 0.25.(C), 0.5(D) & 1(F)
K
0.25
250
350
K
0.25
10R to 1M
250
350
15(Y), 25(D), 50(C), 100(Z)
0.05(W), 0.1(B), 0.25.(C), 0.5(D) & 1(F)
B
0.25
10R to 1M
250
350
15(Y), 25(D), 50(C), 100(Z)
0.05(W), 0.1(B), 0.25.(C), 0.5(D) & 1(F)
C
0.5
10R to 1M
350
500
See resistance
restrictions
L
0.5
10R to 1M
350
500
See resistance
restrictions
1.0
1R to 10M
500
700
See resistance
restrictions
RC65
RC70
Notes
ohms 1R to 1M 1R to 1M 1R to 1M
These tables indicate the CECC specification requirements, and these are met or exceeded by the corresponding RC series products.
Standard values
Thermal impedance
Ambient temperature range
°C/watt
°C
110
E24, E96 preferred
70
-55 to +155
60
Any value
to order
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
07. 11
Urgent! Can anyone tell me why Virtex6 Rapidio modelsim simulation ireq_rdy_n does not go low after being pulled high
[align=left][color=#000000]Hello everyone [font=Calibri] [/font]When I use [font=Calibri]modelsim[/font] to simulate [font=Calibri]Rapidio[/font], when [font=Calibri] [/font] starts to send, [font=Cal...
jasonshows FPGA/CPLD
Typical embedded system components
[b][b][color=#003366][font=Verdana][size=2]Embedded system is a special computer application system. It has the common characteristics of general computer components and is also composed of hardware a...
songbo Embedded System
Method of Mixing C and Assembly Programming in Keil (Part 2)
The assembly function in keil calls the c51 function [ycong_kuang] For the writing method in keil, please refer to post 89852, as follows: Compared with post 89852, the first step is to add a c51 func...
eret Embedded System
51 MCU stack problem
Can the status of ports P0, P1, P2, and P3 be pushed into the stack of the 51 microcontroller? These ports have corresponding registers. I think it is possible. It can also be simulated using Keil+Pro...
19850719 Embedded System
Headhunting position: Beijing Fortune 500 recruits senior Symbian developers - C++
Headhunting position: Beijing Fortune 500 is looking for senior Symbian R&D-C++ with corresponding specific JD. The client is a Fortune 500 foreign company. To do the R&D of smartphone Symbian system,...
qiushui007 Embedded System
About BL9341DC24V-3.3V
When 24DCV is connected to this BUCK circuit for power supply, I would like to ask about the problem of BL9341....
steven321 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2788  1350  1913  1714  1404  57  28  39  35  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号