Marketing Bulletin
DATE:
TO:
FROM:
RE:
May 6, 2005
All Sales Personnel
Mark Stoner
E11 (OS/03) Termination
To all concerned parties,
This bulletin is to notify all customers of the discontinuation of the following Ecliptek
series effective May 1
st
, 2005:
Series
E11
Description
5V 14 pin DIP ECL Oscillator
Recommended Replacement
None
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of
product termination. New orders will not be accepted after August 1
st
, 2005, with
delivery to conclude by November 1
st
2005.
If there are any questions pertaining to this bulletin, please fell free to contact me.
Thank you again for your cooperation.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE
•
COSTA MESA, CA 92626-1401
•
(714) 433-1200
•
Fax (714) 433-1234
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
00
45
25
Operating Temperature Range
Blank
ET
Storage Temperature Range
Supply Voltage (V
EE
)
Input Current
Output Voltage Logic High
Output Voltage Logic Low
Rise/Fall Time
Duty Cycle
Load Drive Capability
Aging @ 25°C
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
PIN
1
7
8
14
6.000MHz to 155.520MHz
(All Values Inclusive of Operating Temp. Range, Supply Voltage, and Load)
±100ppm Max.
±50ppm Max.
±25ppm Max. (0°C to +70°C only), (less than or equal to 125.000MHz only)
0°C to +70°C
-40°C to +85°C
-55°C to +125°C
-5.2Vdc ±5% (AA, AB, and AM); +5.2Vdc ±5% (AC)
140mA Maximum
-1.0Vdc Min./-0.7Vdc Max. (AA, AB, and AM); 4.0Vdc Min./4.5Vdc M ax. (AC)
-1.95Vdc Min./-1.60Vdc Max. (AA, AB, and AM); 3.00Vdc Min./3.42Vdc Max. (AC)
2nSec Maximum (Measured at 20% to 80% of waveform)
50% ±10% (Measured at 50% of waveform)
50 Ohms into -2.0Vdc (AA, AB, and AM); 50 Ohms into +3.0Vdc (AC)
±5ppm/year Maximum
ENVIRONMENTAL & MECHANICAL
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
PIN CONFIGURATIONS
AA
Ground/Case
-5.2V
Output
Ground
AB
No Connect or Complementary Output
-5.2V
Output
Ground/Case
AC
No Connect or Complementary Output
Ground/Case
Output
+5.2Vdc
AM
No Connect or Complementary Output
Ground/Case
Output
-5.2Vdc
PART NUMBERING GUIDE
E11 00 AM ET C - 24.000M - CL175
Configuration Options
CLXXX = Cut Leads (MAL01-101-000)
G = Gull Wing (MAL01-001-000)
Frequency
Pin 1 Connection
Blank = No Connect
C = Complementary Output
Operating Temperature Range
Blank = 0°C to +70°C
ET = -40°C to +85°C
Pin Configuration
AA, AB, AC, or AM
Per Pin Configuration Table Above
Frequency Tolerance/Stability
00 = ±100ppm Maximum, 45 = ±50ppm Maximum
25 = ±25ppm Maximum
7.620
±0.203
1
15.240
±0.203
0.9 MAX
7
∅0.457
±0.1 (X4)
14
8
5.08
MAX
13.2
MAX
5.08
MIN
MARKING GUIDE
(Line #1)
ECLIPTEK
(Line #2)
E11 AM C
Pin 1 Connection
Blank = No Connect
C = Complementary Output
Pin Configuration Per Pin Configuration Table Above
20.8 MAX
ALL DIMENSIONS
IN MILLIMETERS
SPECIFICATION CONTROL DRAWING
Drawing Number
(Line #3)
XXX.XXXM
Frequency
CSC01-010-000
Title
(Line #4)
XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
ECLIPTEK
E11AMC
XXX.XXXM
XXYZZ
FULL SIZE ECL OSCILLATOR
Revision
Effectivity Date
E
ECN Number
08-27-03
PAGE 1 OF 2
Date Released By
Date
8675
NOTE: Pin 1 shall be marked with a black dot. Marking shall
conform to conditions listed in TQC41-001-000.
Approved By
京公网安备 11010802033920号
EEWORLD
