The polarization beam combiner and depolarizer is a compact, high-performance
micro-optic-based depolarizing component. It normally functions as a combiner
to combine two orthogonal-polarized pump beams together and then converts
it to a depolarized beam at the output port. Depending on special customer
requirements, the isolator functionality can be integrated with the depolarizer or
remain as a stand-alone depolarizer without combining functionality.
• Telcordia GR-1221
north america
:
800 498-JDSU (5378)
worlDwiDe
:
+800 5378-JDSU
webSite
:
www.jdsu.com
polarization Beam comBiner anD Depolarizer
2
Dimensions Diagram
PBCD
IPBCD
Standalone depolarizer
All dimensions are mm.
specifications
parameter
pBcD
ipBcD
stand-alone
Depolarizer
Center wavelength, λ
C
Wavelength range, λ
S
Insertion loss
1
Wavelength-dependent loss
Degree of polarization
Isolation
Return loss
Input power
2
Operating temperature
Storage temperature
Tensile load
Dimensions (D x L)
Fiber type
Pigtail color code
Maximum
Maximum
Maximum
Minimum
Minimum
Maximum
Maximum
Maximum
1450 nm
λ
C
±30 nm
0.8 dB
0.9 dB
0.7 dB
0.15 dB
10%
N/A
20 dB
N/A
50 dB
2000 mW
–5 to 75°C
–40 to 85°C
5 N
5.5 x 58 mm
Ports 1 and 2: Panda PM fiber, port 3: SMF-28 fiber
Port 1: black, port 2: clear, port 3: clear
Note: Parameters are specified for the whole wavelength range and operating temperature range without a connector. The direction of linear polarization is aligned with the
slow axis of the PM fiber.
1. Extra loss from pump PER is excluded.
2. Maximum input power for each port is 1000 mW.
polarization Beam comBiner anD Depolarizer
ordering information
For more information on this or other products and their availability, please contact your local JDSU account manager
or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at
customer.service@jdsu.com.
sample: pBD-c34p10000
pBD-
code
C
I
S
code
34P
S34
XXX
Functions
Polarization beam combiner
and depolarizer
Polarization beam combiner
and depolarizer with isolator
Stand-alone depolarizer
pump Dependent
JDSU Raman pump S34+
JDSU Raman pump S34
Others. Please contact JDSU for
further ordering information.
code
1
2
code
0
1
Fiber length
1 m
2 m
Fiber Buffer type
250 µm bare fiber¹
900 µm loose tube
code
0
1
2
3
4
code
0
1
2
3
4
connector² (port 1)
No connector
FC/SPC
FC/APC
SC/SPC
SC/APC
connector² (port 2)
No connector
FC/SPC
FC/APC
SC/SPC
SC/APC
code
0
1
2
3
4
connector² (port 3)
No connector
FC/SPC
FC/APC
SC/SPC
SC/APC
1. Connector is not available on 250 µm bare fiber.
2. Insertion loss and return loss depend on connector type.
I downloaded a testusb program from the Internet http://www.vckbase.com/code/winsys/driver/testusb.rar It is a test program for enumerating USB devices and requires DDK to compile. I used vs2005+ddk b...
I calculated the dead time of 3525 to be 0.13us, but the time interval between the rising edges of the two complementary PWM waves measured was 2us. I calculated the dead time according to the formula...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i]The connection and data exchange between the CPU and external devices and memory need to be realized through interface devices. T...
When I plug in the Kingston 2G USB drive, it is successfully installed and can be used, but after a while it says unknown driver and nothing happens. It is not displayed in my computer or in the taskb...
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
The battery and its management system are one of the key technologies of electric vehicles. In the past few years, most companies have encountered embarrassment in the development of electric vehic...[Details]
The cruise control system (CCS) of a vehicle is also called a constant speed driving system. It is an electronic control device that uses advanced electronic technology to automatically adjust the ...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
1. Electromagnetic compatibility design
Electromagnetic compatibility refers to the ability of electronic equipment to work in a coordinated and effective manner in various electromagnetic env...[Details]
Modern communication equipment, portable electronic products, laptops, electric vehicles, small satellites, etc. generally use batteries as power sources and are widely used. However, the batteries...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
