EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TLAFA3882

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-TLAFA3882 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-TLAFA3882 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1554 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Sound receiving filter circuit
[i=s] This post was last edited by paulhyde on 2014-9-15 03:37 [/i] Sound receiving circuit [[i] This post was last edited by menmendan on 2011-8-8 10:26 [/i]]...
闷闷蛋啊 Electronics Design Contest
Why is the infrared receiver LF0038Y not responsive?
Theoretically, the high level is not close to VCC, and the low level is 0.4V. However, when I actually measured it, it only changed by 0.1-0.2V when irradiated with infrared light. The infrared wavele...
王阿东 Analog electronics
Analog circuit debugging experience - development board rush purchase_3
[i=s]This post was last edited by dontium on 2015-1-23 13:15[/i]Share your debugging experience a little bit, I have used a certain company's clock distribution chip on several boards, with the same c...
jlqsczw_2007 Analogue and Mixed Signal
Problems when compiling Verilog program with ISE software
The problematic statement: assign tc_clkcnt=(clkcnt==16'b0000_0000_1000_0101)?1:0; The warning: Result of 32-bit expression is truncated to fit in 1-bit target. I can't figure out what's wrong with it...
PuesueDream FPGA/CPLD
STM32CubeMX uses LL library to set timer to use external clock mode to control gpio flip
[i=s]This post was last edited by qq825117996 on 2020-9-8 11:56[/i]cube automatically generates initialization function void MX_TIM1_Init(void) {LL_TIM_InitTypeDef TIM_InitStruct = {0};LL_GPIO_InitTyp...
qq825117996 stm32/stm8
PCI9054 local connection problem?
The number of address lines on the local side is 30, how come it is a 32-bit address line? Where are the other two? Is the bus width controlled by LBE[0..3] a data line or an address line? Now there i...
wangtingcaojia Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1098  2308  1403  2216  989  23  47  29  45  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号