EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GG-03-9103-G

Description
Fixed Resistor, Thin Film, 0.25W, 910000ohm, 100V, 2% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GG-03-9103-G Overview

Fixed Resistor, Thin Film, 0.25W, 910000ohm, 100V, 2% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202GG-03-9103-G Parametric

Parameter NameAttribute value
MakerTT Electronics plc
package instruction, 0202
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance910000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeONE SURFACE
Tolerance2%
Operating Voltage100 V
Base Number Matches1
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Ask about the question 1602!!
Could any expert help me look at this program? 1602 shows 0123, the interface is fine, but it just can't be displayed. #include "msp430.h" //reference header file #include "msp430f5438.h" /***********...
zcy609841519 Microcontroller MCU
Research on Code Compression for Embedded Processors (PhD Thesis, Zhejiang University)
[i=s]This post was last edited by paulhyde on 2014-9-15 09:34[/i] For heterogeneous dual-core SOC-GEM-SOC, a pure software code decoding method is proposed. The method is implemented by the CK520 proc...
clark Electronics Design Contest
Source program simulation file based on 51 single-chip multifunctional intelligent desk lamp (with clock, posture correction, display temperature and brightness)
[i=s]This post was last edited by木头12333 on 2020-12-30 12:52[/i]Functional description:1. After power-on, the LED light turns on, indicating that the current lamp is in automatic control mode;2. Press...
木头12333 51mcu
INA common-mode range can be a challenge
When it comes to the common-mode range of instrumentation amplifiers, input/gain overload conditions can cause serious problems. It is important to understand that input/gain overload is not necessari...
wstt Microcontroller MCU
[PSoC4 experience] Warm-up work before waiting for the board
1. Data preparation. 1) The forum download center is very comprehensive, almost all of them do not require points, just choose what you are interested in and download a lot. [url]https://download.eewo...
sacq MCU
2418 There is some progress on the strange problem, but it has not been solved yet. Please help me.
Last time I used 2418, the current was high and it kept resetting.Now I use an adapter (bought with the emulator, 64pin) + 2418.Except for P1.0, which is used to output the LED indicator, the other ex...
fsymd Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 228  1923  409  114  1035  5  39  9  3  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号