EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTN20289802D

Description
RES NET,THIN FILM,898K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

WCTN20289802D Overview

RES NET,THIN FILM,898K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE

WCTN20289802D Parametric

Parameter NameAttribute value
MakerVishay
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance898000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Base Number Matches1
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
Power supply design solutions in medical equipment
[i=s]This post was last edited by qwqwqw2088 on 2014-4-9 08:27[/i] [p=24, 2, left][color=rgb(62, 62, 62)][font=Tahoma, Arial, sans-serif]Transfer[/font][/color][/p][p=24, 2, left][color=rgb(62, 62, 62...
qwqwqw2088 Analogue and Mixed Signal
MOSFET turn-on schedule question
As shown in the figure, Pspice simulates the mosfet turn-on process. The waveform obtained by simulation is shown in the figure (blue is Vds, red is Vgs, and green is Id), which is different from the ...
ujs Analog electronics
About 1602 display problem
Give me the code first, [code]CW DATA 0F9FCH ;write instruction CR DATA 0F9FEH ;read status DIW DATA 0F9FDH ;write data DIR DATA 0F9FFH ;read data ORG 0000H AJMP START ORG 0030H PANYAO: DB 'C51',0 STA...
xyw Embedded System
Air pressure and altitude conversion display
I made a barometric altimeter. The display of barometric pressure has been solved, but the height has not been solved. How can I change the conversion relationship between barometric pressure and heig...
zh7031907 MCU
mega16, I don't know how to write the program to set the upper and lower temperature limits
There is no problem with 1602 LCD display and DS18B20 temperature measurement, but I want to set upper and lower limit alarms. I would like you to teach me or help me write it. Thank you very much. Wr...
Hsmallguy Microchip MCU
Application of TOPSwitch Devices in Power Supplies
Abstract: The integrated control chip that integrates PWM controller and MOSFET power switch is an important feature and trend of the new generation of switching power supply design. This article intr...
zbz0529 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2059  1301  275  1931  969  42  27  6  39  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号