C132680JCG2LF datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> capacitor> C132680JCG2LF

C132680JCG2LF: DescriptionBUSSED C NETWORK, 25V, C0G, 0.000068uF, THROUGH HOLE MOUNT, SIP-13, SIP, ROHS COMPLIANT; CategoryPassive components capacitor; File Size94KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

C132680JCG2LF Overview

BUSSED C NETWORK, 25V, C0G, 0.000068uF, THROUGH HOLE MOUNT, SIP-13, SIP, ROHS COMPLIANT

C132680JCG2LF Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	TT Electronics plc
package instruction	SIP,
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	0.000068 µF
Capacitor type	ARRAY/NETWORK CAPACITOR
length	34.29 mm
Installation features	THROUGH HOLE MOUNT
negative tolerance	5%
Network Type	BUSSED C NETWORK
Number of components	12
Number of functions	1
Number of terminals	13
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
encapsulated code	SIP
Package shape	RECTANGULAR PACKAGE
positive tolerance	5%
Rated (DC) voltage (URdc)	25 V
Maximum seat height	7.62 mm
surface mount	NO
Temperature characteristic code	C0G
Temperature Coefficient	-/+30ppm/Cel ppm/°C
Terminal pitch	2.54 mm
Terminal shape	FLAT
width	3.3 mm
Base Number Matches	1

Preview

Download Datasheet

View All

Single-In-Line Conformal

Coated Capacitor Networks

C Series

Isolated or bussed circuits

4 to 14 Leads

Electrical

Rated Voltage

Capacitance Range

Tolerance

Temperature Coefficient

(% of Change)

Operating Temperature Range

J Tol.

±5%

K Tol.

±10%

M Tol.

±20%

25Vdc, 50Vdc, 100Vdc

10pF to 1μF (Custom 2.2pF to 10pF max.)

Z Tol.

+80% to -20%

Refer to Dielectric Table

CG & X7R: -55°C to +125°C

Y5V: -30°C to +85°C

Dielectric Table

Dielectric

X7R

Y5V

CG (NPO)

Specifications subject to change without notice.

Characteristics

±15% (-55 to +125°C)

+22% to -82% (-30 to +85°C)

±30ppm/°C

Values

1000pF to 1μF

100nF to 1μF

100pF to 1μF

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

03.12

Recommended Resources

USB interface circuit design of FT245BM and FPGA

MAX225-RS232 multi-channel data interface circuit (driver-receiver)

DC motor control circuit driven by AC power_2

22 commonly used diode single-phase rectifier circuits Figure 2

Three capacitor braking circuit

Computer motherboard circuit diagram 810 3_05

Rabbit2000 Embedded Development: Ask you guys: Has anyone used rabbit2000? ? ? How to program the serial port for parity check, data bits 5-9...; hy8457 Embedded System

Design comparison of two wireless digital modems: Author: Bai Xin, Unit 94569 of the Chinese People's Liberation Army Abstract : This paper introduces two wireless digital MODEMs designed and implemented based on CMX469A and MSM7512B, explains the ha...; fighting RF/Wirelessly

Question + How to detect if I2C communication fails during programming?: I used to use analog timing, but I didn't write much. I copied it directly. Recently, I encountered a problem. Communication failed. Later, I increased the delay in some places. It was probably becaus...; youluo Microcontroller MCU

Emulator Problems: I am using a USB emulator, which had been working fine before. However, after I disassembled it yesterday, the system suddenly prompted that it was an unrecognizable USB device, so the driver could no...; totoro3425 Analogue and Mixed Signal

Are the connections of two transistors affected by humidity or temperature?: As shown in the figure: This should be a Darlington connection. It works in the cut-off zone and saturation zone. However, when the humidity is high, it will automatically saturate. Using a hair dryer...; liangben Analog electronics

Dead-band control register not working?: It may be that the carrier frequency is too high and the oscilloscope scanning time is not enough to observe the change of the pulse edge.The upper and lower bridge arm drive pulses should be compleme...; jlmfzhg705 Analogue and Mixed Signal

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components