REVISIONS
LTR
A
B
C
DESCRIPTION
Add vendor CAGE 34333. Add vendor CAGE U4637. Editorial changes
throughout.
Add device types 02, 03, and 04. Editorial changes throughout.
Change vendor CAGE 12969 to 48726. Change max duty cycle min limit. Add
vendor CAGE U4637 for additional devices, also change name form Integrated
Power to Seagate Microelectronics. Add vendor CAGE 34333 for additional
devices. Add testing for delay to output, rise time, and fall time tests. Editorial
changes throughout.
Add packages C, E, F, 2, H, and X. Changes unity gain bandwidth limit.
Editorial changes throughout.
Add device types 05, 06, 07, and 08. Add vendor CAGE 48726 for device type
05, 06, 07, and 08. Changes to table I electricals. Delete vendor CAGE U4637
from drawing. Add vendor CAGE U3158. Editorial changes throughout.
Changes in accordance with NOR 5962-R146-94.
Changes in accordance with NOR 5962-R251-97.
Change vendor CAGE 48726 to 01295. Add class V for vendor CAGE 01295. .
Editorial changes throughout. – lgt
Correction to the V
MIN
limit in table I for device types 03 and 06. Editorial
changes throughout. - rrp
Add case outline D. - ro
DATE (YR-MO-DA)
87-04-16
87-12-21
89-10-10
APPROVED
M. A. Frye
M. A. Frye
M. A. Frye
D
E
92-11-23
93-09-10
M. A. Frye
M. A. Frye
F
G
H
J
K
94-05-17
97-03-19
00-11-08
01-10-10
02-05-30
M. A. Frye
M. A. Frye
R. Monnin
R. Monnin
R. Monnin
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
K
1
K
2
K
3
K
4
K
5
K
6
K
7
K
8
K
9
K
10
K
11
K
12
K
13
PREPARED BY
DONALD R. OSBORNE
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D. A. DiCENZO
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
APPROVED BY
N. A. HAUCK
DRAWING APPROVAL DATE
86-11-10
MICROCIRCUIT, LINEAR, PROGRAMMABLE
PRIMARY SIDE PULSE WIDTH MODULATOR,
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
K
SIZE
A
SHEET
CAGE CODE
14933
1 OF
13
5962-86704
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E410-02
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the
Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the
PIN.
1.2 PIN. The PIN is as shown in the following examples.
For device classes M and Q:
5962
Federal
stock class
designator
\
-
RHA
designator
(see 1.2.1)
\/
Drawing number
For device class V:
5962
Federal
stock class
designator
\
-
RHA
designator
(see 1.2.1)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and
are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
04
05
06
07
08
Generic number
1842
1843
1844
1845
1842A
1843A
1844A
1845A
Circuit function
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
Off-line current mode pulse width modulator controller
86704
01
Device
type
(see 1.2.2)
/
V
Device
class
designator
(see 1.2.3)
C
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
86704
01
Device
type
(see 1.2.2)
/
C
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86704
SHEET
K
2
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed
below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q
designators will not be included in the PIN and will not be marked on the device.
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
C
D
E
F
H
P
X
2
Descriptive designator
GDIP1-T14 or CDIP2-T14
GDFP1-F14 or CDFP2-F14
GDIP1-T16 or CDIP2-T16
GDFP2-F16 or CDFP3-F16
GDFP1-F10 or CDFP2-F10
GDIP1-T8 or CDIP2-T8
CQCC1-N20
CQCC1-N20
Terminals
14
14
16
16
10
8
20
20
Package style
Dual-in-line
Flat pack
Dual-in-line
Flat pack
Flat pack
Dual-in-line
Square leadless chip carrier (see figure 1)
Square leadless chip carrier (see figure 1)
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage (V
CC
) ..................................................................................
Output current .............................................................................................
Output energy (capacitance load) ...............................................................
Analog input voltage (pins 2 and 3) ............................................................
Error amplifier output sink current ...............................................................
Power dissipation (P
D
)(T
A
= +25°C):
Cases C, E, F, H, P, X, and 2 ..................................................................
Case D ....................................................................................................
Storage temperature range .........................................................................
Lead temperature (soldering, 10 seconds) .................................................
Junction temperature (T
J
) ...........................................................................
30 V
±1.0
A
5.0
µ
j
-0.3 V to +6.3 V
10 mA
1.0 W 4/
700 mW 4/
-65°C to +150°C
+300°C
+150°C
Thermal resistance, junction-to-case (
θ
JC
) ................................................ See MIL-STD-1835
1.4 Recommended operating conditions.
Supply voltage (V
CC
) .................................................................................. +15 V
±5.0
percent
Ambient operating temperature range (T
A
) ................................................ -55°C to +125°C
1/
2/
3/
4/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
All voltages are with respect to ground, and all currents are positive when flowing into the specified terminal.
All references to pin numbers are for case outline P.
Derate at 8.0 mW/°C above T
A
= +25°C for case P, 10 mW/°C above T
A
= +50°C for cases C and E,
5.5 mW/°C above T
A
= +25°C for case D, 8.7 mW/°C above T
A
= +25°C for case F,
9.0 mW/°C above T
A
= +40°C for cases 2 and X, and 6.9 mW/°C above T
A
= +25°C for case H.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86704
SHEET
K
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86704
SHEET
K
4
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535
and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain
the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 110 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86704
SHEET
K
5
京公网安备 11010802033920号
EEWORLD
