Operational environment; total dose irradiation testing to MIL-
STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1 Mrad(Si)
- Latchup immune (LET > 100 MeV-cm
2
/mg)
Packaging options:
- 48-lead flatpack (1.4 grams)
Standard Microcircuit Drawing 5962-01535
- QML Q and V compliant part
Compatible with TIA/EIA-644 LVDS standard
INTRODUCTION
The UT54LVDS218 Deserializer converts the three LVDS data
streams back into 21 bits of CMOS/TTL data. At a transmit clock
frequency of 75MHz, 21 bits of TTL data are transmitted at a rate
of 525Mbps per LVDS data channel. Using a 75MHz clock, the
data throughput is 1.575 Gbit/s (197 Mbytes/sec).
The UT54LVDS218 Deserializer allows the use of wide, high
speed TTL interfaces while reducing overall EMI and cable size.
All pins have Cold Spare buffers. These buffers will be high
impedance when V
DD
is tied to V
SS
.
LVDS TO-PARALLEL TTL
DATA (LVDS)
21
CMOS/TTL OUTPUTS
CLOCK (LVDS)
PLL
RECEIVER CLOCK OUT
POWER DOWN
36-00-06-010
Version 1.0.1
Figure 1. UT54LVDS218 Deserializer Block Diagram
1
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
RxOUT 17
RxOUT 18
GND
RxOUT 19
RxOUT 20
N/C
LVDS GND
RxIN0-
RxIN0+
RxIN1-
RxIN1+
LVDS V
DD
LVDS GND
RxIN2-
RxIN2+
RxCLK IN-
RxCLK IN+
LVDS GND
PLL GND
PLL V
DD
PLL GND
PWR DWN
RxCLK OUT
RxOUT0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
UT54LVDS218
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
V
DD
RxOUT 16
RxOUT 15
RxOUT 14
GND
RxOUT 13
V
DD
RxOUT 12
RxOUT 11
RxOUT 10
GND
RxOUT 9
V
DD
RxOUT 8
RxOUT 7
RxOUT 6
GND
RxOUT 5
RxOUT 4
RxOUT 3
V
DD
RxOUT 2
RxOUT 1
GND
PIN DESCRIPTION
Pin Name
RxIN+
RxIN-
RxOUT
RxCLK IN+
RxCLK IN-
RxCLK OUT
PWR DWN
V
DD
GND
PLL V
DD
PLL GND
LVDS V
DD
LVDS GND
I/O
I
I
O
I
I
O
I
I
I
I
I
I
I
No.
3
3
21
1
1
1
1
4
5
1
2
1
3
Description
Positive LVDS differential data inputs
1
Negative LVDS differential data output
1
TTL level data outputs
Positive LVDS differential clock input
Negative LVDS differential clock input
TTL level clock output. The rising edge acts
as data strobe. Pin name RxCLK OUT.
TTL level input. When asserted (low input)
the receiver outputs are low
Power supply pins for TTL outputs and log-
ic
Ground pins for TTL outputs and logic
Power supply for PLL
Ground pin for PLL
Power supply pin for LVDS pins
Ground pins for LVDS inputs
Notes:
1. These receivers have input fail-safe bias circuitry to guarantee a stable receiver
output for floating or terminated receiver inputs. Under these conditions receiver
inputs will be in a HIGH state. If a clock signal is present, data outputs will all be
HIGH; if the clock input is also floating/terminated outputs will remain in the last
valid state. A floating/terminated clock input will result in a LOW clock output.
Figure 2. UT54LVDS218 Pinout
LVDS CABLE
TX
TxIN
0
1
2
MEDIA DEPENDENT DATA
(LVDS)
RX
RxOUT
0
1
2
CMOS/
TTL
18
19
20
18
19
20
CLOCK
(LVDS)
TxCLK
GND
PCB
SHIELD
Figure 3. UT54LVDS218 Typical Application
36-00-06-010
Version 1.0.1
2
PCB
RxCLK
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
OPERATIONAL ENVIRONMENT
PARAMETER
Total Ionizing Dose (TID)
Single Event Latchup (SEL)
Neutron Fluence
1
Notes:
1. Guarnteed but not tested.
LIMIT
1.0E6
>100
1.0E13
UNITS
rad(Si)
MeV-cm
2
/mg
n/cm
2
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 4.0V
-0.3 to (V
DD
+ 0.3V)
-65 to +150C
1.25 W
+150C
10C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
4. For cold spare mode (V
DD
= V
SS
), V
I/O
may be -0.3V to the maximum recommended operating V
DD
+0.3V.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6V
-55 to +125C
0V to V
DD
36-00-06-010
Version 1.0.1
3
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
DC ELECTRICAL CHARACTERISTICS*
1
(V
DD
= 3.0V to 0.3V; -55C < T
C
< +125C); Unless otherwise noted, Tc is per the temperature noted.
SYMBOL
PARAMETER
CONDITION
MIN
MAX
UNIT
CMOS/TTL DC SPECIFICATIONS (PWR DWN, RXOUT)
V
IH
V
IL
V
OL
V
OH
I
IH
I
IL
V
CL
I
CS
I
OS2,3
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
High-level input current
Low-level input current
Input clamp voltage
Cold spare leakage current
Output short circuit current
I
OL
= 2mA
I
OL
= -0.4mA
V
IN
=3.6V; V
DD
= 3.6V
V
IN
=0V; V
DD
= 3.6V
I
CL
= -18mA
V
IN
=3.6V; V
DD
= V
SS
V
OUT
= 0V
-20
-15
2.7
-10
-10
+10
+10
-1.5
+20
-130
2.0
GND
V
DD
0.8
0.3
V
V
V
V
A
A
V
A
mA
LVDS RECEIVER DC SPECIFICATIONS (IN+, IN-)
V
V
3
V
CMR4
I
IN
Differential input high threshold
Differential input low threshold
Common mode voltage range
Input current
V
CM
= +1.2V
V
CM
= +1.2V
V
ID
=210mV
V
IN
= +2.4V, V
DD
= 3.6V
V
IN
= 0V, V
DD
= 3.6V
I
CSIN
Cold spare leakage current
V
IN
= 3.6V, V
DD
= V
SS
-100
0.2
-10
-10
-20
2.00
+10
+10
+20
+100
mV
mV
V
A
A
A
Supply Current
I
CC3
I
CCPD
Active supply current
Power down supply current
CL=8pF (see Figure 5)
PWR DWN = Low, LVDS inputs =
logic low, V
DD
= 3.6V
105
2.0
m
mA
Notes:
* For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25
o
C per MIL-STD-883 Method 1019, Condition
A up to the maximum TID level procured.
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I
OS
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time for a maximum duration
of one second.
3. Guaranteed by characterization.
4. Tested functionally.
36-00-06-010
Version 1.0.1
4
Cobham Semiconductor Solutions
www.aeroflex.com/LVDS
RECEIVER SWITCHING CHARACTERISTICS*
1
(V
DD
= 3.0V to 3.6V; Tc = -55C to +125C); Unless otherwise noted, Tc isper the temperature ordered.
SYMBOL
CLHT
3
CHLT
3
RSPos0
3
RSPos1
3
RSPos2
3
RSPos3
3
RSPos4
3
RSPos5
RSPos6
3
3
PARAMETER
CMOS/TTL Low-to-High Transition Time (Figure 5)
CMOS/TTL High-to-Low Transition Time (Figure 5)
Receiver Input Strobe Position for Bit 0 (Figure 10)
Receiver Input Strobe Position for Bit 1 (Figure 10)
Receiver Input Strobe Position for Bit 2 (Figure 10)
f=75MHz
Receiver Input Strobe Position for Bit 3 (Figure 10)
f=75MHz
Receiver Input Strobe Position for Bit 4 (Figure 10)
f=75MHz
Receiver Input Strobe Position for Bit 5 (Figure 10)
f=75MHz
Receiver Input Strobe Position for Bit 6(Figure 10)
f=75MHz
RxCLK OUT Period (Figure 6)
f=75MHz
RxCLK OUT High Time (Figure 6)
f=75MHz
RxCLK OUT Low Time (Figure 6)
f=75MHz
RxOUT Setup to RxCLK OUT (Figure 6)
RxOUT Hold to RxCLK OUT (Figure 6)
f=75MHz
RxCLK IN to RxCLK OUT Delay (Figure 7)
f=75MHz
Receiver Phase Lock Loop Set (Figure 8)
f=75MHz
Receiver Powerdown Delay (Figure 9)
f=75MHz
f=75MHz
MIN
MAX
3.5
3.5
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
0.50
2.41
4.31
6.22
8.12
10.03
11.93
13.3
3.6
3.6
3.5
3.5
3.4
1.24
3.15
5.05
6.96
8.86
10.77
12.67
66.7
RCOP
3
RCOH
3
RCOL
3
RSRC
4
RHRC
4
RCCD
2
RPLLS
5
RPDD
8.3
10
2
ns
ms
s
Notes:
* For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25
o
C per MIL-STD-883 Method 1019, Condition
A up to the maximum TID level procured.
1. Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account the transmitter pulse positions (min and max)
and the receiver input setup and hold time (internal data sampling window). This margin allows LVDS interconnect skew, inter-symbol interference (both dependent
on type/length of cable), and source clock jitter less than 250 ps (calculated from T
POS
- R
POS
) - see Figure 11.
2. Total latency for the channel link chipset is a function of clock period and gate delays through the transmitter (TCCD) and receiver (RCCD). The total latency for
LVDS217 Serializer and the LVDS218 Deserializer is (T + TCCD) + 2*T + RCCD), where T = Clock period.
Question: My supervisor requires a graduation project, an 8086 simulation based on protues. One of the experiments requires the use of an 8254A chip, but I don't know what 8254A is called in protues?...
On February 19, 2022, Tesla announced through its official social platform that it had produced the one millionth 4680 battery in January .
At Tesla's Battery Day held in September last year, Tesla do...
After reading the document, I feel that the protection measures are no different from those of MEGA88.ATMEL refuses to admit that MEGA88 can be decrypted. However, it is true that you can get the comp...
As the title says, add a toolbar to a dialog-based project, add a button and a close cross on it, and it can be used normally. I have tried many times, but it doesn't work....
Use Renesas MCU to read the data of MPU6050, use 24101 to send the status data of the mouse to the receiving end connected to the computer, and control the computer mouse to complete the movement, scr...
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
As more and more consumers purchase new energy vehicles, the safety of electric vehicles has become a major concern. This has been particularly prominent following a series of electric vehicle fire...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
A pure sine wave inverter has a good output waveform with very low distortion, and its output waveform is essentially the same as the AC waveform of the mains power grid. In fact, the AC power prov...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
