5962-9458505H4A datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9458505H4A

5962-9458505H4A: DescriptionEEPROM Module, 128KX32, 140ns, Parallel, CMOS, CPGA66; Categorystorage storage; File Size374KB，42 Pages; ManufacturerAeroflex; Websitehttp://www.aeroflex.com/

Download Datasheet Parametric View All

5962-9458505H4A Overview

EEPROM Module, 128KX32, 140ns, Parallel, CMOS, CPGA66

5962-9458505H4A Parametric

Parameter Name	Attribute value
Maker	Aeroflex
package instruction	PGA, PGA66,11X11
Reach Compliance Code	unknown
Maximum access time	140 ns
Data polling	YES
JESD-30 code	S-XPGA-P66
memory density	4194304 bit
Memory IC Type	EEPROM MODULE
memory width	32
Number of terminals	66
word count	131072 words
character code	128000
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	CERAMIC
encapsulated code	PGA
Encapsulate equivalent code	PGA66,11X11
Package shape	SQUARE
Package form	GRID ARRAY
page size	128 words
Parallel/Serial	PARALLEL
power supply	5 V
Certification status	Not Qualified
Filter level	38535Q/M;38534H;883B
Maximum standby current	0.005 A
Maximum slew rate	0.25 mA
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	MILITARY
Terminal form	PIN/PEG
Terminal pitch	2.54 mm
Terminal location	PERPENDICULAR
switch bit	NO
write protect	SOFTWARE
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Added device type 06 for vendor cages 54230 and 88379. Added

vendor cage 0EU86 for device types 01 through 06. Figure 1,

changed case outline M to reflect package is available in either a

single or dual cavity. -sld

Added case outline 9.

Added device types 07, 08, and 09 for vendor cage 0EU86. Made

changes to table I to include the addition of device types 07, 08, and

09. Added a min limit to the table I for the I

, and the I

tests. Made

changes to Figures 2, 3, 4, 5, 6, and 8. -sld

Added case outline Z. Updated paragraph 1.2.4, 1.3, figures 1, 2,

and 8. -sld

DATE (YR-MO-DA)

99-05-14

APPROVED

K. A. Cottongim

00-04-06

02-01-31

Raymond Monnin

02-06-04

Raymond Monnin

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Gary Zahn

CHECKED BY

Michael C. Jones

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS

AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

AMSC N/A

DEFENSE SUPPLY CENTER COLUMBUS

POST OFFICE BOX 3990

COLUMBUS, OHIO 43216-5000

APPROVED BY

Kendall A. Cottongim

MICROCIRCUIT, HYBRID, MEMORY,

DIGITAL, 128K x 32-BIT, ELECTRICALLY

ERASABLE/PROGRAMMABLE READ ONLY

MEMORY

SIZE

SHEET

CAGE CODE

DRAWING APPROVAL DATE

94-08-02

REVISION LEVEL

67268

1 OF

5962-94585

DSCC FORM 2233

APR 97

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5962-E373-02

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in

the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the

solicitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.

HANDBOOKS

DEPARTMENT OF DEFENSE

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in

accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as

designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class.

Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534).

Furthermore, the manufacturers may take exceptions or use alternate methods to the tests and inspections herein and not

perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device

class.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38534 and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.

3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, 6, and 7.

3.2.5 Block diagram. The block diagram shall be as specified on figure 8.

3.2.5 Typical output test circuit. The typical output test circuit shall be as specified on figure 9.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full specified operating temperature range.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

SIZE

REVISION LEVEL

5962-94585

SHEET

DSCC FORM 2234

APR 97

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Programming procedure. The programming procedure shall be as specified by manufacturer and shall be available on

request.

3.6 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with

the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked as listed in MIL-HDBK-103

and QML-38534.

3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described

herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot

sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for

those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer

and be made available to the preparing activity (DSCC-VA) upon request.

3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this

drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets

the performance requirements of MIL-PRF-38534 and herein.

3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

microcircuits delivered to this drawing.

3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This

reprogrammability test shall be done for the initial characterization and after any design or process changes which may affect

the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of

program/erase endurance cycles listed in section 1.3 herein over the full specified operating temperature range. The vendor's

procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity.

3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall

be done for initial characterization and after any design or process change which may affect data retention. The methods and

procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military

temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of

the acquiring or preparing activity.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

SIZE

REVISION LEVEL

5962-94585

SHEET

DSCC FORM 2234

APR 97

Recommended Resources

Current output circuit of DAC0832

Sonic remote control circuit

Improved XW62 spindle motor control circuit

Mechanical switch contacts - interface to CMOS integrated circuits

50uA current source circuit diagram

Infrared sensing music socket circuit using SR5553

What is impedance matching?: [i=s] This post was last edited by paulhyde on 2014-9-15 09:18 [/i] What is impedance matching?...; miaorui2008 Electronics Design Contest

Let's take a look at the motherboard of this phone.: HTC ONE motherboardInterestingly, the back of the motherboard is almost entirely copper-clad, and no vias can be seen. Judging from the density on the front, the board is full of blind and buried vias...; wstt PCB Design

MCU interface technology practical subroutine supporting source code download: Single-chip microcomputer interface technology practical subroutine supporting source code download...; tdgtan555 MCU

Album--55 EDA simulation related albums: [Book Collection] Detailed Explanation of 100 Examples of VHDL Language [url=https://bbs.eeworld.com.cn/thread-97963-1-11.html]https://bbs.eeworld.com.cn/thread-97963-1-11.html[/url] [Book Collection]...; wzt FPGA/CPLD

Power Factor Correction: Power Factor CorrectionPower factor correction (PFC) is mainly used to improve the ratio of effective power to apparent power at the input of the power supply. It is one of the common circuits in swit...; okhxyyo Power technology

Request PT22622272 schematic diagram: I want to get some PT2262 and 2272 recently. Does anyone have pictures or information to share with me? Thanks in advance....; fengxin RF/Wirelessly

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components