EEWORLDEEWORLDEEWORLD

Part Number

Search

CAT1026YI-28-GT2

Description
2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
Categoryaccessories   
File Size227KB,20 Pages
ManufacturerCatalyst
Websitehttp://www.catalyst-semiconductor.com/
Download Datasheet View All

CAT1026YI-28-GT2 Overview

2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8

CAT1026, CAT1027
Dual Voltage Supervisory Circuits with
I
2
C Serial 2k-bit CMOS EEPROM
FEATURES
Precision V
CC
Power Supply Voltage Monitor
5V, 3.3V and 3V systems
Five threshold voltage options
Additional voltage monitoring
Externally adjustable down to 1.25V
Watchdog timer (CAT1027 only)
Active High or Low Reset
Valid reset guaranteed at V
CC
= 1V
400kHz I
2
C Bus
2.7V to 5.5V Operation
Low power CMOS technology
16-Byte Page Write Buffer
Built-in inadvertent write protection
1,000,000 Program/Erase cycles
Manual Reset capability
100 year data retention
Industrial and extended temperature ranges
8-pin DIP, SOIC, TSSOP, MSOP or TDFN
(3 x 3mm foot-print) packages
TDFN max height is 0.8mm
For Ordering Information details, see page 19.
The CAT1027 is designed with a 1.6 second
watchdog timer circuit that resets a system to a known
state if software or a hardware glitch halts or “hangs”
the system. The CAT1027 features a watchdog timer
interrupt input, WDI.
The on-chip 2k-bit EEPROM memory features a 16-byte
page. In addition, hardware data protection is provided
by a V
CC
sense circuit that prevents writes to memory
whenever V
CC
falls below the reset threshold or until V
CC
reaches the reset threshold during power up.
Available packages include 8-pin DIP and surface
mount, 8-pin SO, 8-pin TSSOP, 8-pin TDFN and 8-pin
MSOP packages. The TDFN package thickness is
0.8mm maximum. TDFN footprint is 3 x 3mm.
supply monitor and reset circuit protects memory and
systems controllers during power up/down and
against brownout conditions. If power supply voltages
are out of tolerance reset signals become active
preventing the system microcontroller, ASIC, or
peripherals from operating.
The CAT1026 features two open drain reset outputs:
¯¯¯¯¯¯
one (RESET) drives high and the other (RESET)
drives low whenever V
CC
falls below the threshold.
Reset outputs become inactive typically 200ms after
the supply voltage exceeds the reset threshold value.
With both active high and low reset signals, interface
to microcontrollers and other ICs is simple. CAT1027
¯¯¯¯¯¯
¯¯¯¯¯¯
has only a RESET output. In addition, the RESET pin
can be used as an input for push-button manual reset
capability.
The CAT1026 and CAT1027 provide an auxiliary
voltage sensor input, V
SENSE
, which is used to monitor
a second system supply. The auxiliary high impe-
dance comparator drives the open drain output, V
LOW
,
whenever the sense voltage is below 1.25V threshold.
DESCRIPTION
The CAT1026 and CAT1027 are complete memory
and supervisory solutions for microcontroller-based
systems. A 2k-bit serial EEPROM memory and a
system power supervisor with brown-out protection
are integrated together in low power CMOS techno–
logy. Memory interface is via a 400kHz I
2
C bus.
The CAT1026 and CAT1027 provide a precision V
CC
sense circuit with five reset threshold voltage options
that support 5V, 3.3V and 3V systems. The power
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-3010 Rev. M
How to analyze lithium battery bulging and leakage?
Three of the lithium batteries in a batch purchased by the company were bulging and leaking. Since they were bought from Taobao, we cannot ask the supplier to analyze the cause of the battery swelling...
天天1 Analog electronics
10000RMB looking for part-time staff for mobile software development
The company wants to make a software for smart phones, the requirements are as follows: The system can automatically collect relevant network data of mobile terminals and automatically generate measur...
zyq26672607 Embedded System
Emergency assistance
[font=黑体][size=6]Excuse me, how to test the bq24160 power chip? Is there a complete typical application circuit diagram? Is there any that has been tested? [/size][/font]...
2367385505 Analogue and Mixed Signal
TMP112 temperature sensor can't be fixed
Yesterday, I used TI's low-power temperature sensor TMP112, the microcontroller is MSP430F2132, and used IO to simulate I2C. The sensor always did not respond after writing the second byte. The first ...
chende815 Microcontroller MCU
Quenching the thirst of RF power amps and extending the life
In tracking the average power, high peak-to-average power ratio (PAPR) signals are clipped and therefore distorted (i.e., linearity is compromised), which is why this method is most attractive for low...
JasonYoo RF/Wirelessly
Analysis of Difficulties in PCB Selective Soldering Process
In the PCB electronic industry welding process, more and more manufacturers are beginning to turn their attention to selective welding. Selective welding can complete all solder joints at the same tim...
ohahaha PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2767  2214  590  2584  860  56  45  12  53  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号