EEWORLDEEWORLDEEWORLD

Part Number

Search

CAT1021LI-25-T3

Description
Supervisory Circuit with I2C Serial 2K CMOS EEPROM. Manual Reset and Watchdog Timer Monitors SDA
File Size188KB,21 Pages
ManufacturerCatalyst
Websitehttp://www.catalyst-semiconductor.com/
Download Datasheet View All

CAT1021LI-25-T3 Overview

Supervisory Circuit with I2C Serial 2K CMOS EEPROM. Manual Reset and Watchdog Timer Monitors SDA

CAT1021, CAT1022, CAT1023
Supervisory Circuits with I
2
C Serial 2k-bit CMOS
EEPROM, Manual Reset and Watchdog Timer
FEATURES
Precision Power Supply Voltage Monitor
— 5V, 3.3V and 3V systems
— Five threshold voltage options
Watchdog Timer
Active High or Low Reset
— Valid reset guaranteed at V
CC
= 1V
400kHz I C Bus
2.7V to 5.5V Operation
Low power CMOS technology
16-Byte Page Write Buffer
Built-in inadvertent write protection
— WP pin (CAT1021)
1,000,000 Program/Erase cycles
Manual Reset Input
100 year data retention
Industrial and extended temperature ranges
8-pin DIP, SOIC, TSSOP, MSOP or TDFN
(3 x 3mm foot-print) packages
— TDFN max height is 0.8mm
All supervisors have a 1.6 second watchdog timer circuit
that resets a system to a known state if software or a
hardware glitch halts or “hangs” the system. For the
CAT1021 and CAT1022, the watchdog timer monitors
the SDA signal. The CAT1023 has a separate watchdog
timer interrupt input pin, WDI.
The power supply monitor and reset circuit protect
memory and system controllers during power up/down
and against brownout conditions. Five reset threshold
voltages support 5V, 3.3V and 3V systems. If power
supply voltages are out of tolerance reset signals
become active, preventing the system microcontroller,
ASIC or peripherals from operating. Reset signals
become inactive typically 200 ms after the supply voltage
exceeds the reset threshold level. With both active high
and low reset signals, interface to microcontrollers and
¯¯¯¯¯¯
other ICs is simple. In addition, the RESET pin or a
separate input, ¯¯¯, can be used as an input for push-
MR
button manual reset capability.
The on-chip, 2k-bit EEPROM memory features a 16-byte
page. In addition, hardware data protection is provided
by a V
CC
sense circuit that prevents writes to memory
whenever V
CC
falls below the reset threshold or until V
CC
reaches the reset threshold during power up.
Available packages include an 8-pin DIP and surface
mount 8-pin SO, 8-pin TSSOP, 8-pin TDFN and 8-pin
MSOP packages. The TDFN package thickness is
0.8mm maximum. TDFN footprint options are 3 x 3mm.
2
DESCRIPTION
The CAT1021, CAT1022 and CAT1023 are complete
memory and supervisory solutions for microcontroller-
based systems. A 2k-bit serial EEPROM memory and a
system power supervisor with brown-out protection are
integrated together in low power CMOS technology.
Memory interface is via a 400kHz I
2
C bus.
The CAT1021 and CAT1023 provide a precision V
CC
sense circuit and two open drain outputs: one (RESET)
¯¯¯¯¯¯
drives high and the other (RESET) drives low whenever
V
CC
falls below the reset threshold voltage. The
¯¯¯¯¯¯
CAT1022 has only a RESET output and does not have
a Write Protect input. The CAT1021 also has a Write
Protect input (WP). Write operations are disabled if WP
is connected to a logic high.
For Ordering Information details, see page 19.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-3009 Rev. M
Introduction to UC3842 protection power supply circuit solution
UC3842 adopts fixed working frequency pulse width controllable modulation mode, with a total of 8 pins, the functions of each pin are as follows: ① pin is the output end of the error amplifier, and th...
qwqwqw2088 Analogue and Mixed Signal
lm3s8970 CAN interrupt? ?
I am using LM3S8970 software IAR for CAN communication. How can I read the value of CAN interrupt register? Can I read it directly using HWREG (register address)? The read value is not the pending int...
lijob Embedded System
How does GPRS transmit PPP data?
When transmitting PPP protocol data (LCP, PAP) via GPRS, since the PDP context has not yet been established, how should it be transmitted - should it be processed according to the layer 3 protocol sta...
icove Embedded System
How to effectively charge lead-acid batteries with unstable low voltage?
I bought a 100 watt 24 volt solar panel, how come it has almost no effect on charging a 24 volt lead battery?...
g6g6 Power technology
I am new to edk and have two questions.
As a beginner, I have done 6 experiments of EDK and feel that I have a basic understanding of EDK. I would like to ask you some questions:1. I want to open someone else's project file, but the result ...
qd0090 FPGA/CPLD
A verified testbenches module
Beginners can download it and take a look. . ....
383077599 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 234  1880  841  2602  1746  5  38  17  53  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号