Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
TTL compatible inputs and output levels, three-state
bidirectional data bus
Typical radiation performance
- Total dose: 50krads
- >100krads(Si), for any orbit, using Aeroflex UTMC
patented shielded package
- SEL Immune >80 MeV-cm
2
/mg
- LET
TH
(0.25) = >10 MeV-cm
2
/mg
- Saturated Cross Section (cm
2
) per bit, 5.0E-9
-<1E-8 errors/bit-day, Adams to 90% geosynchronous
heavy ion
Packaging options:
- 36-lead ceramic flatpack (weight 3.42 grams)
- 36-lead flatpack shielded (weight 10.77 grams)
Standard Microcircuit Drawing 5962-00536
- QML T and Q compliant part
INTRODUCTION
The QCOTS
TM
UT9Q512 Quantified Commercial Off-the-
Shelf product is a high-performance CMOS static RAM
organized as 524,288 words by 8 bits. Easy memory expansion
is provided by an active LOW Chip Enable (E), an active LOW
Output Enable (G), and three-state drivers. This device has a
power-down feature that reduces power consumption by more
than 90% when deselected
.
Writing to the device is accomplished by taking Chip Enable
one (E) input LOW and Write Enable (W) inputs LOW. Data on
the eight I/O pins (DQ
0
through DQ
7
) is then written into the
location specified on the address pins (A
0
through A
18
). Reading
from the device is accomplished by taking Chip Enable one (E)
and Output Enable (G) LOW while forcing Write Enable (W)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E) HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOWand W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT9Q512 SRAM Block Diagram
1
DEVICE OPERATION
A0
A1
A2
A3
A4
E
DQ0
DQ1
V
DD
V
SS
DQ2
DQ3
W
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
The UT9Q512 has three control inputs called Enable 1 (E),
Write Enable (W), and Output Enable (G); 19 address inputs,
A(18:0); and eight bidirectional data lines, DQ(7:0). E Device
Enable controls device selection, active, and standby modes.
Asserting E enables the device, causes I
DD
to rise to its active
value, and decodes the 19 address inputs to select one of 524,288
words in the memory. W controls read and write operations.
During a read cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
1
0
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. UT9Q512 25ns SRAM Pinout (36)
(For both shielded and unshielded packages)
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Enable
Write Enable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) and E less than V
IL
(max) defines a read cycle. Read access time is measured from
the latter of Device Enable, Output Enable, or valid address to
valid data output.
SRAM Read Cycle 1, the Address Access in figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Device
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 3b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 3c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable - Controlled Access in figure
4a, is defined by a write terminated by W going high, with E
still active. The write pulse width is defined by t
WLWH
when the
write is initiated by W, and by t
ETWH
when the write is initiated
by E. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable - Controlled Access in figure
4b, is defined by a write terminated by E going inactive. The
write pulse width is defined by t
WLEF
when the write is initiated
by W, and by t
ETEF
when the write is initiated by the E going
active. For the W initiated write, unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the eight bidirectional
pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1E-8
krad(Si)
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 10% worst case particle environment, Geosynchronous orbit, 0.025 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
PARAMETER
Positive supply voltage
Case temperature range
LIMITS
4.5 to 5.5V
(C) screening: -55° to +125°C
(E) screening: -40° to +125°C
V
IN
DC input voltage
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(-55°C to +125°C for (C) screening and -40
o
C to +125
o
C for (W) screening) (V
DD
= 5.0V + 10%)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(TTL)
(TTL)
I
OL
= 8mA, V
DD
=4.5V (TTL)
I
OL
= 200µA,V
DD
=4.5V (CMOS)
I
OH
= -4mA,V
DD
=4.5V (TTL)
I
OH
= -200µA,V
DD
=4.5V (CMOS)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
IN
= V
DD
and V
SS,
V
DD
= V
DD
(max)
V
O
= V
DD
and V
SS
V
DD
= V
DD
(max)
G = V
DD
(max)
V
DD
= V
DD
(max), V
O
= V
DD
V
DD
= V
DD
(max), V
O
= 0V
I
DD
(OP)
Supply current operating
@ 1MHz
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
I
DD1
(OP)
Supply current operating
@40MHz
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E = V
DD
- 0.5
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
-55°C and 25°C
-40°C and 25°C
125°C
180
mA
125
mA
-2
-2
2.4
3.2
10
12
2
2
CONDITION
MIN
2.0
0.8
0.4
0.05
MAX
UNIT
V
V
V
V
V
V
pF
pF
µA
µA
I
OS2, 3
Short-circuit output current
-90
90
mA
I
DD2
(SB)
Supply current standby
@0MHz
6
6
12
mA
mA
mA
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
[i=s]This post was last edited by 770781327 on 2014-11-28 21:58[/i] My computer is Windows 8. I want to study the camera routine. But I have to use Camera-test.exe when running it. But when I click on...
[b]1. Introduction[/b] In the field of industrial field control, programmable logic controller (PLC) has always played an important role. With the increasing investment of the state in the water suppl...
This event isAs one of the general activities, we look forward to your suggestions on the use, application and promotion of TI Stellaris, so that more engineers can use TI Stellaris series products.
A...
Is there a mechanism, for example, I am running in the fun() function now, and I want to get which function the CPU called before calling the fun function in this function, is this possible? When I am...
[align=left][font=Helvetica]It has accounted for a certain proportion of the entire electronic system (for example, [/font]1/3), which is usually called a high-frequency circuit. High-frequency circui...
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
Electric motors and internal combustion engines of the same power have similar torque levels. High power requires high torque, and torque determines a vehicle's acceleration speed, commonly known a...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
With the advancement of science and technology and the promotion of green, energy-saving, and circular development, the demand for precise control and accurate measurement is increasing. In the pow...[Details]
AI distributed rendering architecture improves mobile phone rendering capabilities, and game performance tests can check frame generation indicators in real time
Shanghai, China, Aug...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
Recently, a research team from Shandong University and Huawei Technologies Co., Ltd. achieved a significant breakthrough in the field of power semiconductors. Using fluorine-ion implantation termin...[Details]
Momenta's self-developed assisted driving chip has been successfully launched and entered the actual vehicle testing phase. This is the first time that Momenta has "settled" its own algorithm on an...[Details]
This article uses a heavy-duty off-road vehicle as an example to design a gateway and body control software based on a domain controller (DC). The article also examines the feasibility of u...[Details]
Principle of single-phase AC motor
The starting methods of 220V AC single-phase motors are roughly divided into the following categories:
The first type, split-phase starting, as shown in...[Details]
By integrating Ceva's NeuPro-Nano and NeuPro-M neural processing units (NPUs) into ALi's VDSS platform, it provides efficient AI acceleration for intelligent edge devices
, thereby driving th...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
