EEWORLDEEWORLDEEWORLD

Part Number

Search

86506-231H

Description
Board Connector, 31 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size418KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

86506-231H Overview

Board Connector, 31 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

86506-231H Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBREAKAWAY TYPE
body width0.095 inch
subject depth0.1 inch
body length3.1 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (15) OVER NICKEL (50)
Contact completed and terminatedTIN LEAD (150) OVER NICKEL (50)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1500VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYCYCLOHEXYLENE TEREPHTHALLATE
JESD-609 codee0
Manufacturer's serial number86506
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature130 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts31
Base Number Matches1
How to expand FPGA control SDR SDRAM
I recently used FPGA to make an SDRAM controller. It was originally connected to one SDRAM, and it has been debugged OK. Now I need to expand the capacity. I don't know how to connect two SDRAMs? The ...
eeleader-mcu FPGA/CPLD
Smart Grid Power Quality Monitor-Solution Introduction
[i=s]This post was last edited by elvike on 2016-12-25 22:30[/i] [align=left][font=宋体]A word of caution before the beginning: I haven't posted anything for a long time. I went back and looked through ...
elvike Industrial Control Electronics
Questions about the use of TVS tubes and voltage regulator tubes
I have the impression that the principle used by Zener diodes and TVS tubes is that the voltage does not change much in a large current change range. Therefore, a general Zener diode is connected in s...
陈陈陈1 Analog electronics
About Magnetic Beads
I have some ferrite beads, MMZ2012 series, 60 ohm, 1000mA maximum current, I want to use it for power supply, but the data sheet of this ferrite bead says that this series is for signal line, can I us...
hsleung PCB Design
Determination of ARM s3c44b0x ISR_STARTADDRESS value
Recently, I ran an interrupt program on the s3c44b0x board, and it always failed. After considering all the situations, I think the ISR_STARTADDRESS value is a possible error. The source program defin...
doctorwu ARM Technology
Looking for CCS3.3 software
A novice is learning DSP and using a classmate's software. After installing it, for some reason a message pops up asking for a repair license, so the software cannot be opened.So I need help from you ...
buaawumeng DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2026  762  173  2742  2764  41  16  4  56  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号