radiation-hardened, 32K x 8 programmable memory device. The
UT28F256LVQLE PROM features fully asychronous operation
requiring no external clocks or timing strobes. An advanced
radiation-hardened twin-well CMOS process technology is used
to implement the UT28F256LVQLE. The combination of
radiation-hardness, fast access time, and low power consumption
make the UT28F256LQLE ideal for high speed systems designed
for operation in radiation environments.
A(14:0)
DECODER
MEMORY
ARRAY
SENSE AMPLIFIER
CE
PE
OE
PROGRAMMING
CONTROL
LOGIC
DQ(7:0)
Figure 1. PROM Block Diagram
1
DEVICE OPERATION
The UT28F256LVQLE has three control inputs: Chip Enable
(CE), Program Enable (PE), and Output Enable (OE); fifteen
address inputs, A(14:0); and eight bidirectional data lines,
DQ(7:0). CE is the device enable input that controls chip
selection, active, and standby modes. Asserting CE causes I
DD
to rise to its active value and decodes the fifteen address inputs
to select one of 32,768 words in the memory. PE controls
program and read operations. During a read cycle, OE must be
asserted to enable the outputs.
PIN CONFIGURATION
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
DD
PE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
PIN NAMES
A(14:0)
CE
OE
PE
DQ(7:0)
Address
Chip Enable
Output Enable
Program Enable
Data Input/Data Output
Table 1. Device Operation Truth Table
1
OE
X
0
1
1
PE
1
1
0
1
CE
1
0
0
0
I/O MODE
Three-state
Data Out
Data In
Three-state
MODE
Standby
Read
Program
Read
2
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
Thermal resistance, junction-to-case
2
DC input current
LIMITS
-0.3 to 6.0
-0.5 to (V
DD
+ 0.5)
-65 to +150
1.5
+175
3.3
UNITS
V
V
°C
W
°C
°C/W
mA
±
10
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the
device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2. Test per MIL-STD-883, Method 1012, infinite heat sink.
2
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6
-55 to +125
0 to V
DD
UNITS
V
°C
V
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 3.0V to 3.6V; -55°C < T
C
< +125°C)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN 1
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance, all inputs
except PE
Input Capacitance PE
C
IO 1
I
IN
Bidirectional I/O capacitance
ƒ
= 1MHz, V
DD
= 3.3V
V
OUT
= 0V
V
IN
= 0V to V
DD
, all pins except PE
V
IN
= V
DD
, PE only
V
O
= 0V to V
DD
V
DD
= 3.6V
OE = 3.6V
V
DD
= 3.6V, V
O
= V
DD
V
DD
= 3.6V, V
O
= 0V
CMOS input levels (I
OUT
= 0), V
IL
=
0.2V
V
DD
, PE = 3.6V, V
IH
= 3.0V
CMOS input levels V
IL
= V
SS
+0.25V
CE = V
DD
- 0.25 V
IH
= V
DD
- 0.25V
-3
I
OL
= 100µA, V
DD
= 3.0V
I
OL
= 1.0mA, V
DD
= 3.0V
I
OH
= -100µA, V
DD
= 3.0V
I
OH
= -1.0mA, V
DD
= 3.0V
ƒ
= 1MHz, V
DD
= 3.3V
V
IN
= 0V
V
DD
-0.15
V
DD
-0.3
15
CONDITION
MINIMUM
0.7V
DD
0.25V
DD
V
SS
+ 0.05
V
SS
+ 0.10
MAXIMUM
UNIT
V
V
V
V
V
V
pF
20
15
pF
µA
µA
µA
Input leakage current
+3
35
+8
I
OZ
Three-state output leakage
current
-8
I
OS 2,3
I
DD1
(OP)
4
Short-circuit output current
100
-100
mA
mA
Supply current operating
@15.4MHz (65ns product)
50.0
1.0
mA
mA
I
DD2
(SB)
post-rad
Supply current standby
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rad(Si).
1. Measured only for initial qualification, and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
4. 1.7mA/MHz.
3
READ CYCLE
A combination of PE greater than V
IH
(min), and CE less than
V
IL
(max) defines a read cycle. Read access time is measured
from the latter of device enable, output enable, or valid address
to valid data output.
An address access read is initiated by a change in address inputs
while the chip is enabled with OE asserted and PE deasserted.
Valid data appears on data output, DQ(7:0), after the specified
t
AVQV
is satisfied. Outputs remain active throughout the entire
cycle. As long as device enable and output enable are active, the
address inputs may change at a rate equal to the minimum read
cycle time.
AC CHARACTERISTICS READ CYCLE (Post-Radiation)*
(V
DD
= 3.0V to 3.6V; -55°C < T
C
< +125°C)
SYMBOL
t
AVAV1
t
AVQV
t
AXQX2
t
GLQX2
t
GLQV
t
GHQZ
t
ELQX2
t
ELQV
t
EHQZ
PARAMETER
Read cycle time
Read access time
Output hold time
OE-controlled output enable time
OE-controlled access time
OE-controlled output three-state time
CE-controlled output enable time
CE-controlled access time
CE-controlled output three-state time
The chip enable-controlled access is initiated by CE going active
while OE remains asserted, PE remains deasserted, and the
addresses remain stable for the entire cycle. After the specified
t
ELQV
is satisfied, the eight-bit word addressed by A(14:0)
appears at the data outputs DQ(7:0).
Output enable-controlled access is initiated by OE going active
while CE is asserted, PE is deasserted, and the addresses are
stable. Read access time is t
GLQV
unless t
AVQV
or t
ELQV
have
not been satisfied.
28F256LV-65
MIN
MAX
65
65
0
0
35
35
0
65
35
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rads(Si).
1. Functional test.
2. Three-state is defined as a 200mV change from steady-state output voltage.
4
t
AVAV
A(14:0)
CE
t
ELQX
t
ELQV
OE
t
GLQV
DQ(7:0)
t
GLQX
t
AVQV
t
AXQX
t
GHQZ
t
AVQV
t
EHQZ
Figure 2. PROM Read Cycle
RADIATION HARDNESS
The UT28F256LVQLE PROM incorporates special design and
layout features which allow operation in high-level radiation
environments. Aeroflex Colorado Springs has developed special
low-temperature processing techniques designed to enhance the
total-dose radiation hardness of both the gate oxide and the field
oxide while maintaining the circuit density and reliability. For
RADIATION HARDNESS DESIGN SPECIFICATIONS
1
Total Dose
Latchup LET Threshold
Memory Cell LET Threshold
Logic SEU Onset LET
SEU Cross Section
transient radiation hardness and latchup immunity, Aeroflex
Colorado Springs builds all radiation-hardened products on
epitaxial wafers using an advanced twin-tub CMOS process. In
addition, Aeroflex Colorado Springs pays special attention to
power and ground distribution during the design phase,
minimizing dose-rate upset caused by rail collapse.
1E6
>110
>100
>40
7.6E-12
2.5E-17
rad(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
MeV-cm
2
/mg
cm
2
/bit
errors/bit day
Error rate - geosynchronous orbit, Adams 90% worst case environment
Note:
1. The PROM will not latchup during radiation exposure under recommended operating conditions.
If GPIO is used as chip select and read/write enable for peripheral devices, then the data bus of the external device cannot use the data bus of 2812, right?This connection method should be equivalent...
I received the board today and tried it. It didn't light up and there was a compilation error, as shown in the picture. I initially thought that something was missing from the software. Do you have an...
As the title says, I have an array of type short. I want to store it as a text file. How can I do that? I hope an expert can give me some advice. Thank you!...
Job requirements: 1. Bachelor degree or above; 2. Proficient in analog and digital circuits, and have a very in-depth understanding of various electronic components; 3. More than ten years of work exp...
I would like to ask how does the MSP convert the analog signal into a digital signal after the voltage signal output by the strain sensor is amplified by the operational amplifier? What is the input v...
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
On August 22, Lantu Motors officially launched its Lanhai Intelligent Hybrid technology via an online livestream. This intelligent hybrid technology, which integrates a full-range 800V high-voltage...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
On August 18th, Galaxis, a specialist in integrated intelligent intralogistics robotics, officially unveiled its next-generation, ultra-narrow aisle forklift mobile robot, the "VFR Ultra-Narrow Ser...[Details]
A half-bridge is an inverter topology for converting DC to AC. A typical half-bridge circuit consists of two controller switches, a three-wire DC power supply, two feedback diodes, and two capacito...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
A patent disclosed by Ford proposes replacing traditional segmented side curtain airbags with integrated full-width side curtain airbags that span the side of the vehicle and can be deployed simult...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
The driving mode is not unfamiliar to vehicles. According to the driving mode of the vehicle, there are front-wheel drive, rear-wheel drive and even four-wheel drive. Four-wheel drive is a major se...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
Summer is the peak season for buying and using air conditioners. Do you pay attention to the energy efficiency of your air conditioner? Did you buy a DC inverter air conditioner? Do you know the re...[Details]
With the prevalence of online conferencing, live streaming, and voice communication in gaming, high-quality audio input devices are becoming increasingly important. To this end, XMOS, an expert in ...[Details]
introduction
The widespread use of air conditioner communication circuits began with the rise of household inverter air conditioners. With China's energy conservation and emission reduction in...[Details]
Since the beginning of the 21st century, with the rapid development of my country's urban and rural economies and the improvement of people's living standards, more and more people have begun to ow...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
