The dual output DFC10 Series provides power solutions to meet
commercial and industrial requirements. With power densities
above 11 watts per cubic inch (0.67 watts per cm
3
), overcurrent
protection, and five sided shielded case, the DFC10 meets rigorous
needs in an industry standard case size. The 120KHz operating
frequency of the DFC10 Series allows an increased power density
while including adequate heat sinking and input/output filtering.
This eliminates the need for external components in most
applications. Full overload protection is provided by pulse-by-pulse
current limiting on models with 48V input.
FEATURES
•
High Power Density, up to 11 Watts per Cubic Inch
•
Efficiencies to 79%
•
Fully Isolated, Fully Filtered Design
•
Greater than 700V Isolation
•
Overcurrent Protection
•
Five-Side Shielded Copper Case
•
Ultra Wide Range Input (4:1)
BOTTOM VIEW
2.02
(51.31)
0.300
(7.62)
0.000
0.100
(2.54)
0.200
(5.08)
0.500
(12.70)
0.61
(15.5)
0.61
(15.5)
0.000
1
4
2
5
3
SIDE VIEW
0.040 (1.02)
DIA TYP
1.02
(25.91)
0.800
(20.32)
Mechanical tolerances unless otherwise noted:
X.XX dimensions: ±0.03 inches
X.XXX dimensions: ±0.005 inches
NOTES
(1)
All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted.
Refer to the Technical Reference Section for the definition of terms, measurement circuits and other
information.
Case is tied to the COMMON output pin.
The functional temperature range is intended to give an additional data point for use in evaluating this
power supply. At the low functional temperature the power supply will function with no side effects,
however, sustained operation at the high functional temperature will reduce expected operational life.
The data sheet specifications are not guaranteed beyond the case operating range.
The case thermal impedance is specified as the case temperature rise over ambient per package watt
dissipated.
(2)
(3)
(4)
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,
or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are
subject to change without notice.
Rev. 04/2000
1
0.42
(10.67)
0.3
(7.62)
0.000
DFC10 SERIES – DUAL OUTPUT
NOTES
(1)
All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise
noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits
and other information.
Noise is measured per Technical Reference Section. Measurement bandwidth is 0-20 MHz. RMS
noise is measured over a 0.01-1 MHz bandwidth. To simulate standard PCB decoupling practices,
output noise is measured with a 10µf tantalum and 0.01µF ceramic capacitor located 1 inch away
from the converter.
The converter may be safely operated at any load from zero to the full rating. Dynamic response of
the converter may degrade if the converter is operated with less than 25% output load.
Load regulation is defined for loading/unloading both outputs simultaneously. Load range is 25 to
100%.
Cross regulation is defined for loading/unloading one output while the other output is kept at
full load. Load range is 25 to 100%.
Short term stability is specified after a 30 minute warmup at full load, constant line and
recording the drift over a 24 hour period.
DFC10 SERIES APPLICATION NOTES:
External Capacitance Requirements
No external capacitance is required for operation of the DFC10
Series. If a capacitive input source is farther than 1” from the
converter, an additional capacitor may be required at the input
pins for proper operation. This input capacitor should have an
ESR greater than 0.25 ohms. Input capacitors with an ESR less
than 0.25 ohms may cause peaking of the input filter and actually
degrade circuit performance.
External output capacitance is not required for operation,
however it is recommended that 1 F to 10 F of tantalum and
0.001 to 0.1 F ceramic capacitance be selected for reduced system
noise. Additional output capacitance may be added for increased
1. Introduction to ZigBee
ZigBee is a low-power LAN protocol based on the IEEE802.15.4 standard. According to international standards, ZigBee technology is a short-range, low-power wireless communicat...
I am using AD, the schematic has been drawn, and there is no problem importing it into PCB. However, when I make changes on the schematic, an error occurs when updating to PCB, and all components are ...
Here are some posts from the Internet to give you an understanding of Latch and FF. Latch and flip-flop are both sequential logic, the difference is: latch is related to all its input signals, when th...
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
Leakage current is generated by parasitic resistance paths between the measurement circuit and a nearby voltage source. This current can significantly reduce the accuracy of low current measurement...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
