PH1-PS2LC2845 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-PS2LC2845

PH1-PS2LC2845: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-PS2LC2845 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-PS2LC2845 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Is Samacsys	N
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Communication standards	GR-253
Connection Type	LC/SPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1533 nm
Nominal optical power output	0.562 mW
minimum return loss	-27 dB
Base Number Matches	1

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

TX2/RX2 circuit-a

Electromagnetic bimetal tuning fork oscillator circuit

Input status indication circuit

50A 150VPWM DC drive circuit

IGBT switch equivalent circuit and turn-on waveform

Absolutely usable switching power supply: SONY F29 power supply

Super regenerative receiver module with extremely simple circuit: Original author: Mu Mu Dong Gua This circuit was referenced from a remote control receiver two years ago. It can't be said to be a copy, because I just borrowed the circuit form, and did not completel...; 呱呱 RF/Wirelessly

There seems to be something wrong with the embedded power supply design: ]121. Power supply design121.1. Selection of bypass capacitor for LDO Due to ESR, according to the LDO specification, ESR has a great influence on LDO output. Try to use capacitors with larger ESR val...; 欧阳生 Energy Infrastructure?

The solution of communication between single chip microcomputer and Kingview software: ：This article describes the application of KingView software in the field of industrial control, two solutions for communication between KingView software and single-chip microcomputers and their adva...; frozenviolet MCU

How to save HICON to a file on Wince?: Many APIs on PC are not supported by CE, which makes it very troublesome to set up. Has anyone tried it?...; 圣剑 Embedded System

Design issues on embedded web servers: I am going to do a topic in this area recently, and I will temporarily decide on the Linux platform. However, I am not very familiar with this area, and I hope that brothers and sisters who know about...; foxyboss Embedded System

I want to practice it, please help me: Use a single-chip microcomputer to make an acquisition system. The input signal is 0-10mv, the maximum frequency is 100KHz, and the frequency and voltage value of the input signal are displayed in rea...; chenych MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components