Back
Subminiature Basic Switch
A Variety of D2F-series Models
Including Models Incorporating
Simulated Hinge Lever and Hinge Roller
Lever
Subminiature switch (12.8 x 6.5 x 5.8 (W x H x D))
ideal for PCB mounting.
Incorporating a reverse mechanism made with two
highly precise split springs which ensures a long
service life (1,000,000 operations).
Two-stage bottom different in level and insertion
terminals prevents flux penetration.
PCB, self-standing, solder, and right angle
terminals are available.
Ideal for home electronics equipment, audio
equipment, office machines, and communications
equipment.
D2F
RC
Ordering Information
Actuator
Terminals
Microvoltage/current load
0.1 A
Low operating
force (75 gf)
Pin p u ge
plunger
PCB terminals
Self-clinching
terminals
Solder terminals
Right angle
terminals
Hinge lever
ge e e
PCB terminals
Self-clinching
terminals
Solder terminals
Right angle
terminals
S u a ed
Simulated hinge lever
ge e e
PCB terminals
Self-clinching
terminals
Solder terminals
Right angle
terminals
Hinge roller lever
ge o e e e
PCB terminals
Self-clinching
terminals
Solder terminals
Right angle
terminals
D2F-01F
D2F-01F-T
D2F-01F-D
D2F-01F-A
D2F-01FL
D2F-01FL-T
D2F-01FL-D
D2F-01FL-A
D2F-01FL3
D2F-01FL3-T
D2F-01FL3-D
D2F-01FL3-A
D2F-01FL2
D2F-01FL2-T
D2F-01FL2-D
D2F-01FL2-A
General-purpose
(150 gf)
D2F-01
D2F-01-T
D2F-01-D
D2F-01-A
D2F-01L
D2F-01L-T
D2F-01L-D
D2F-01L-A
D2F-01L3
D2F-01L3-T
D2F-01L3-D
D2F-01L3-A
D2F-01L2
D2F-01L2-T
D2F-01L2-D
D2F-01L2-A
1A
Low operating
force (75 gf)
D2F-F
D2F-F-T
D2F-F-D
D2F-F-A
D2F-FL
D2F-FL-T
D2F-FL-D
D2F-FL-A
D2F-FL3
D2F-FL3-T
D2F-FL3-D
D2F-FL3-A
D2F-FL2
D2F-FL2-T
D2F-FL2-D
D2F-FL2-A
Standard
3A
General-purpose
(150 gf)
D2F
D2F-T
D2F-D
D2F-A
D2F-L
D2F-L-T
D2F-L-D
D2F-L-A
D2F-L3
D2F-L3-T
D2F-L3-D
D2F-L3-A
D2F-L2
D2F-L2-T
D2F-L2-D
D2F-L2-A
115
D2F
D2F
Specifications
Ratings
OF max.
150 g
Item
Rated voltage
Note:
125 VAC
30 VDC
3A
2A
1A
0.5 A
Standard
75 g
Resistive load
---
0.1 A
Microvoltage/current load
150 g
75 g
Consult your OMRON representative before using the switch with inductive or motor loads.
Approved Standards
UL (File No. E32667)/CSA (LR21642)
D2F-01 series: 0.1 A at 30 VDC
D2F-F series: 1 A at 125 VAC, 0.5 A at 30 VDC (100,000 cycles)
D2F-j series: 3 A at 125 VAC, 2 A at 30 VDC
Contact Form
COM
NO
NC
Characteristics
Operating speed
Operating frequency
(at pin plunger)
Insulation resistance
Contact resistance
Dielectric strength
1 to 500 mm/s (at pin plunger)
Mechanical: 200 operations/min
Electrical: 30 operations/min
100 MΩ min. (at 500 VDC)
Standard: 30 mΩ max. (initial value)
Microvoltage/current load: 100 mΩ max. (initial value)
600 VAC, 50/60 Hz for 1 min between contacts of the same polarity
1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal part
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Malfunction: 300 m/s
2
(approx. 30G)
Mechanical: 1,000,000 operations min. (OT value)
Electrical: 30,000 operations min.
Operating: –25°C to 85⁄° (with no icing)
Operating: 85% max.
Approx. 0.5 g
Vibration resistance
Shock resistance
Life expectancy
Ambient temperature
Ambient humidity
Weight (at pin plunger)
116
D2F
Operating Characteristics
Model
OF max.
RF min.
PT max.
OT min.
MD max.
FP max.
OP
Model
OF max.
RF min.
OT min.
MD max.
FP max.
OP
D2Fj, D2F-01j
1.47 N (150 gf)
0.20 N (20 gf)
0.5 mm
0.25 mm
0.12 mm
---
5.5±0.3 mm
D2F-L3j, D2F-01L3j
0.78 N (80 gf)
0.05 N (5 gf)
0.5 mm
0.45 mm
13 mm
8.5±1.2 mm
D2F-FL3j, D2F-01FL3j
0.39 N (40 gf)
0.02 N (2 gf)
0.5 mm
0.45 mm
D2F-Fj, D2F-01Fj
0.74 N (75 gf)
0.05 N (5 gf)
0.5 mm
0.25 mm
0.12 mm
---
D2F-Lj, D2F-01Lj
0.78 N (80 gf)
0.05 N (5 gf)
---
0.55 mm
0.5 mm
10 mm
6.8±1.5 mm
D2F-L2j, D2F-01L2j
0.78 N (80 gf)
0.05 N (5 gf)
0.55 mm
0.5 mm
16.5 mm
13±2 mm
D2F
D2F-FLj, D2F-01FLj
0.25 N (25 gf)
0.02 N (2 gf)
---
0.55 mm
0.5 mm
D2F-FL2j, D2F-01FL2j
0.39 N (40 gf)
0.02 N (2 gf)
0.55 mm
0.5 mm
Engineering Data
Mechanical Life Expectancy
10,000
7,000
Without load
Operating frequency: 60 operations/min
Electrical Life Expectancy
300
Operating frequency: 30/min
Ambient temperature: 25°±3°C
Ambient humidity:
70% max.
100
125 VAC
50
30
20
10
30 VDC
Number of operations (x10
3
)
5,000
3,000
1,000
700
500
300
100
0
OT (mm)
Number of operations (x10
3
)
Switching current (A)
117
D2F
D2F
Dimensions
Note:
1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
3. The following illustrations and drawings are for D2F models with PCB terminals. Self-standing, solder, and right angle terminals are
omitted from the following drawings. Refer to page 119 for these terminals. When ordering, replace
j
with the code for the terminal
that you need.
Pin Plunger
D2Fj
D2F-01j
D2F-Fj
D2F-01Fj
+0.12
2.2
0
12.7
1.2
dia.
5.2
PT
+0.12
2
0
dia. holes
5.7
2.9
5
+0.12
2
0
OP
1.5
3.5
3.15
6.5±0.1
5.08
5.08
12.8±0.15
0.9
0.4
5.8±0.15
Hinge Lever
D2F-Lj
D2F-01Lj
D2F-FLj
D2F-01FLj
12.8
(10.8)
t = 0.3 (see note)
3
FP
OP
Note:
Stainless steel lever
Simulate Hinge Lever
D2F-L3j
D2F-01L3j
D2F-FL3j
D2F-01FL3j
12.7
(7.5)
10
1.3R
FP
2.1
t = 0.3 (see note)
3
OP
Note:
Stainless steel lever
Hinge Roller Lever
D2F-L2j
D2F-01L2j
D2F-FL2j
D2F-01FL2j
12.8
(10)
4
4.8
×
2.8 dia. (resin roller)
(4.6)
t = 0.3
(see
note)
4
OP FP
Note:
Stainless steel lever
118
D2F
Terminals
PCB Terminals
D2F
D2F
Solder Terminals
D2F-D
1.5
3.5
3.15
6.5±0.1
5.08
5.08
12.8±0.15
0.9
0.4
5.8±0.15
Three, 0.8 dia. holes
3.15
6.5±0.1
5.08
5.08
12.8±0.15
1.5 2.4
1.6
0.4
5.8±0.15
Self-clinching Terminals
D2F-T
Right Angle Terminals
D2F-A
1.5
3.4
3.15
6.5±0.1
0.9
0.4
1.25±0.15
5.8±0.15
1.6±0.15
1.5
3.15
6.5±0.1
5.08
5.08
12.8±0.15
1.5
2.6
0.9
0.4
5.8±0.15
3.1
5.08
5.08
12.8±0.15
Precautions
Mounting
When mounting the switch to a PCB, refer to the following mounting
dimensions. The gap between adjacent terminals is two pitches (2 x
2.54 cm).
Mounting Dimensions
2.54
6.5
±
0.15
5.8
±
0.15
2.54
Use M2 mounting screws with plain or spring washers to mount the
switch. Tighten the screws to a torque of 0.08 to 0.1 N
S
m (0.8 to
1 kgf
S
cm).
Mounting Holes
Two , 2 dia. mounting holes
5.08
±
0.1
12.8
±
0.15
Three, 1.2
dia. holes
When soldering the relay terminals, use 6:4 solder and apply a sol-
dering iron rated at 30 W and finish soldering within three seconds.
After soldering, do not move the soldered terminals for at least one
minute.
Make sure that each adjacent terminals of the switch are properly
insulated from each other and the terminals and ground is properly
insulated.
Use of molded fittings is recommended to secure the switch.
Mounting with Molded Pin
Two dia. molded pins
Switch
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B36-E1-6
119
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
