[size=3][color=#ff0000]1. Warning 280:'i':unreferenced local variable[/color] Explanation: The local variable i is not accessed in any way in the function. Solution: Eliminate the declaration of the v...
1. Overview MSP430F149 has three clock sources: external LF (XT1 is generally 32.768K), HF (XT2 is generally 8M), internal DCO. Three clock signals can be obtained from the clock system module: MCLK, ...
I use LPC23XX to implement SD card file storage, but I find that the speed is very slow, mainly because it takes a long time to create a file, up to 180ms. Can an expert tell me why it takes so long? ...
Recently, the U.S. Department of Commerce announced that it would prohibit companies in the country from selling any electronic technology or communication components to ZTE, a Chinese communicatio...[Details]
ZTE
The communication embargo incident has impacted the communication industry and sounded the alarm for the semiconductor industry. Let's follow the embedded editor to learn more about the r...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
I recently upgraded MDK to V5.25 and found that there are many libraries in the Managing Run-Time Environment. Compared with the past, it is much better, from the bottom-level driver to the upper-le...[Details]
This part of the code in the void SystemClock_Config(void) function in the main file generated by stm32cubemx RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; This bug occurs, and the f...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
From the functional classification, it can be divided into: 1. Active control ADAS: ACC/AEB/LKS, etc. 2. Warning ADAS: FCW/LDW/PCW, etc. 3. Other auxiliary ADAS: BSD/ADB/panora...[Details]
The analog watchdog of the ADC is used to check if the voltage is out of bounds. It has two upper and lower bounds, which can be set in the registers ADC_HTR and ADC_LTR respectively. The library fun...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
The photovoltaic industry has become a new business card for China to the world. It not only represents China's leading technology, but also constantly breaks various records with its development spee...[Details]
A crystal oscillator can be electrically equivalent to a two-terminal network consisting of a capacitor and a resistor in parallel and a capacitor in series. In electrical engineering, this network h...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
;The hardware connection circuit of the 51 single-chip microcomputer is as follows: ;P1.3 and P1.4 are each connected to a button; ;P0.0 and P0.3 are each connected to a light-emitting diode; ;P2.0~P...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
