EEWORLDEEWORLDEEWORLD

Part Number

Search

8614-00-14-1-YD-02-716

Description
Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size195KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

8614-00-14-1-YD-02-716 Overview

Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, Solder Terminal

8614-00-14-1-YD-02-716 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (8)
Contact completed and terminatedGOLD (8)
Contact point genderMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number8614
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded1
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts14
UL Flammability Code94V-0
Base Number Matches1
PDM: Rev:A
STATUS:
Released
Printed: Sep 13, 2007
.
2009 China Wireless Portal DIY Competition
2009 China Wireless Portal National DIY Contest This article address: [url]http://www.anywlan.com/bbs/thread-26644-1-1.html[/url] Planning: [url=http://bbs.anywlan.com/]China Wireless Portal[/url] Thi...
tange RF/Wirelessly
Introduction to SPI NAND flash
[backcolor=rgb(222, 240, 251)] In the field of embedded systems, NOR flash and NAND flash, as storage devices, should be familiar to everyone. The interface of early NOR flash was in the form of paral...
13691982107 Medical Electronics
How to implement low voltage alarm (alarm below 12V)?
The microcontroller uses at89s52. I want to realize the low voltage alarm. The voltage in the car is about 12.8v after the engine is turned off. If you use electrical appliances without starting the c...
markov Embedded System
Wince 6.0 key press without interruption
wince 6.0 pxa270 1*1 key, connected in a matrix manner. No interrupt is generated when the key is pressed. Part of the code is as follows [code] XLLP_BOOL_T XllpKeyPadConfigure(XLLP_KEYPAD_REGS *v_pKe...
260658 Embedded System
Question: How much overhead does the STM32 function call have?
Platform: IAR5.30 ST-LINK Use 3IN1 board and STM32 FWLIB. The system works at 72MHz, initializes GPIO speed to 50MHz, and does not open any interrupts. while (1) { //GPIO_LED->BSRR = GPIO_Pin_6 | GPIO...
guoyaru123 stm32/stm8
DSP2812 full comparison PWM output problem
I use 2812 full comparison unit to generate PWM. Among them, PWM1, PWM3, and PWM5 output 1KHz, 40% duty cycle PWM waves, and PWM2, PWM4, and PWM6 output complementary waveforms. Now I find two problem...
xzyxtt DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1437  670  2887  2129  2818  29  14  59  43  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号