EEWORLDEEWORLDEEWORLD

Part Number

Search

MR2525L

Description
Trans Voltage Suppressor Diode, 23V V(RWM), Unidirectional,
CategoryDiscrete semiconductor    diode   
File Size79KB,4 Pages
ManufacturerMotorola ( NXP )
Websitehttps://www.nxp.com
Download Datasheet Parametric View All

MR2525L Overview

Trans Voltage Suppressor Diode, 23V V(RWM), Unidirectional,

MR2525L Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codeunknown
ECCN codeEAR99
Breakdown voltage nominal value40 V
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
JESD-609 codee0
polarityUNIDIRECTIONAL
Maximum repetitive peak reverse voltage23 V
surface mountNO
Terminal surfaceTin/Lead (Sn/Pb)
Base Number Matches1
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MR2535L/D
Advance Information
Overvoltage
Transient Suppressors
. . . designed for applications requiring a low voltage rectifier with reverse
avalanche characteristics for use as reverse power transient suppressors.
Developed to suppress transients in the automotive system, these devices
operate in the forward mode as standard rectifiers or reverse mode as power
avalanche rectifier and will protect electronic equipment from overvoltage
conditions.
Avalanche Voltage 24 to 32 Volts
High Power Capability
Economical
Increased Capacity by Parallel Operation
MR2535L
MR2535S
MEDIUM CURRENT
OVERVOLTAGE
TRANSIENT
SUPPRESSORS
Mechanical Characteristics
Case: Epoxy, Molded
Weight: 2.5 grams (approximately)
Finish: All External Surfaces Corrosion Resistant and Terminal Leads are
Readily Solderable
Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds
Polarity: cathode polarity band
MR2535L shipped 1000 units per plastic bag. Available Tape and Reeled,
800 units per reel by adding a “RL” suffix to the part number.
MR2535S shipped pocket tape and reeled, 500 per 13″ reel
Marking: MR2535L, MR2535S
MAXIMUM RATINGS
Rating
DC Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Repetitive Peak Reverse Surge Current
(Time Constant = 10 ms, Duty Cycle
1%, TC = 25°C) (See Figure 1)
Average Rectified Forward Current
(Single Phase, Resistive Load, 60 Hz, TC = 150°C)
Non–Repetitive Peak Surge Current
Surge Supplied at Rated Load Conditions
Halfwave, Single Phase
Operating and Storage Junction Temperature Range
Symbol
VRRM
VRWM
VR
IRSM
IO
IFSM
CASE 194–04
CATHODE
CASE 421A–01
Value
20
Unit
Volts
110
35
600
Amps
Amps
Amps
TJ, Tstg
–65 to +175
°C
THERMAL CHARACTERISTICS
Characteristic
Thermal Resistance, Junction to Lead @ Both Leads to Heat Sink,
Equal Length
Thermal Resistance Junction to Case
*Typical
This document contains information on a new product. Specifications and information herein are subject to change without notice.
Lead
Length
1/4″
3/8″
1/2″
Symbol
R
θJL
Max
7.5
10
13
0.8*
Unit
°C/W
R
θJC
°C/W
Rev 2
©
Rectifier
Inc. 1996
Data
Motorola,
Device
1
Ask for help either
How was your previous study?...
毛大爷唉 Embedded System
How do you write a graduation thesis on the general introduction to electronic information engineering?
[8-)] I am a freshman at a university in Changchun. We have a course called Introduction to the Subject. After finishing it this week, the teacher asked us to write a 2,000-word paper based on the cur...
52784533 MCU
Ideas about VHDL language syntax.
[size=6]I am a newbie and would like to ask you a question. I want to use VHDL language to output 8 bits of data from an IO port within one clock cycle. How can I write it? Do you have any ideas? [/si...
jinghong21 FPGA/CPLD
Timer_A sets the timer to one second
I have a stupid question: How to use Timer_A to achieve one second timing? I see that Timer_A is 16 bits, and I use a 32.768K crystal oscillator, which cannot achieve such a long time of one second. I...
x700xt Microcontroller MCU
STEVAL-MKI109V3 Unico-GUI cannot connect, prompting The adapter board has not been recognized
Help: Unico-GUI cannot connect to STEVAL-MKI109V3 Open Unico-GUI, select STEVAL-MKI197V1(LSM6DSOX), and click Select Device. Pop-up window prompt: ERROR: The adapter board has not been recognized The ...
凯意法 MEMS sensors
[Xianji HPM6750 Review] +LVGL modified the touch screen, but failed, there was a problem with the touch
I am going to modify the touch screen so that it can be used on the Atom screen. After a day of modification, I finally found that the touch screen is broken. Let's take a look at my modification firs...
流行科技 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1206  1447  1559  2768  1635  25  30  32  56  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号