EEWORLDEEWORLDEEWORLD

Part Number

Search

800Z-GL2Q4Y-

Description
Zero-Force Touch Buttons
File Size145KB,4 Pages
ManufacturerALLEN BRADLEY
Download Datasheet View All

800Z-GL2Q4Y- Overview

Zero-Force Touch Buttons

Two-Hand Control Devices
Zero-Force Touch Buttons
800Z General Purpose
Specifications
Standards
Approvals
Power Supply
Relay Output
Transistor Output
Power Consumption
Relay Output
Transistor Output
Outputs
Relay Output
Transistor Output
Output Ratings
Relay Output
Transistor Output
Min. Switched Current/
Voltage (Relay Output)
Pollution Degree
Operating Temperature
Humidity
Enclosure Protection
Material
Housing/Guard Valox
357
Gaskets BUNA-N
Relay Contacts AgSnO
Any position
5 wire (single common)
4 wire (single common)
10-40V DC, 20-30V AC, or 85-264V AC
10-30V DC
1.44W, 19.2VA
100mA at 24V DC = 2.23W (no load)
1 N.O. & 1 N.C.
PNP or NPN
See Load Life Curves
150mA
8mA/5V DC
2
-25°C to +55°C (-13° to +131°F)
95% RH
IP66 (NEMA 4/4X/13), 1200 psi
washdown
EN574, EN954-1, IEC/EN60947-5-1,
IEC/EN60204-1
cULus, C-Tick, and CE marked for all
applicable directives
Description
The general purpose Bulletin 800Z Zero-Force Touch Buttons are
designed for use by machine control systems requiring the use of
two hands. An interlinked sensor surface weaves two capacitive
sensors in offset planes for superior product sensitivity.
The 800Z touch buttons are ergonomically designed for ease of
operation. No force is required to operate the switch; simply
touching the surface of the switch will initiate an output. The 800Z
can detect the hand though most industrial gloves.
The contour of the 800Z touch buttons serves two purposes; it
easily conforms to the shape of the hand while helping prevent
defeatability when two-hand control is needed.
Two bi-coloured diagnostic LEDs provide guidance during operation.
The power/fault LED blinks at different rates to provide diagnostic
information to the user. The 800Z detects the presence of a hand
during power-up, noise, and conductive film build-up over time.
Mounting
Cable
Features
Zero Force to operate
Ergonomic design
EMC protection
Diagnostic LEDs
Electrical Life
EM-Relay inductive load See Load Life Curves
Vibration
1.5mm (0.06in) 10-55Hz
Shock
100g,11ms half-sine
Load Life Curves for General Purpose Product Line
Relay Output—Maximum DC Load Breaking Capacity
300
200
100
DC Voltage
Relay Output—Electrical Endurance
10
250V AC
10
Resistive Load
Operations
6
50
40
30
20
10
0.1 0.2 0.5
10
5
cosϕ = 1
cosϕ = 0.7
cosϕ = 0.4
1
2
5
10
20
10
4
0
1
2
3
4
5
6
7
8
DC Current (A)
Switching Current (A)
11-2
Altera's 11.0 development software is out. Has anyone used it?
11.0 is out, I installed it and tried it. It feels good, and I also used the DSP one. . . . . . Has anyone used it?Its driver package is very large, integrating QuartusII and NIOSII together. . . . Th...
shilaike FPGA/CPLD
Play with AT32F437 (4) --- Using SPI transmission as an example to explore the internal flash performance
[i=s]This post was last edited by RCSN on 2021-12-24 21:06[/i]According to the Yatli propaganda, AT32F437 can reach up to 4M flash and 512K ram. The model of the host is AT32F437VMT7, which happens to...
RCSN Domestic Chip Exchange
2015 China (Shanghai) International Rehabilitation Nursing and Health Exhibition
CIHE 2015 China (Shanghai) International Health Industry Exhibition 2015 China (Shanghai) International Health Industry Exhibition 2015 Shanghai International Rehabilitation Nursing and Health Mainten...
hjj7777777 Medical Electronics
Ask for a simple question about analog circuit
I cannot set the static operating point properly. According to the data, when IB is about 10uV and VCE is about 8V, the IC should be more than 4MA. Why is it inconsistent with the simulation result? I...
hy5239 Analog electronics
[Mil MYC-JX8MPQ review] + QT calls OpenCV library for testing
After we compile the OpenCV library, we still need to test it, and finally test it on the lower computer, so I chose to use QT for a cross-compilation and run OpenCV using the QT graphical interface. ...
流行科技 Special Edition for Assessment Centres
Please help to write AVR microcontroller program (compiled with iccavr and simulated with proteus)
Basic requirements for LCD display design based on atmega128: 1 Input data from the keyboard through the virtual terminal, and display the received data on the LCD screen. 2 Change the display mode by...
睫毛上的水晶 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2571  1892  2365  520  500  52  39  48  11  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号