PH1-NI2LA3765 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-NI2LA3765

PH1-NI2LA3765: DescriptionTransponder, LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-NI2LA3765 Overview

Transponder, LC/SPC Connector,

PH1-NI2LA3765 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Communication standards	GR-253, OC-192, SONET
Connection Type	LC/SPC CONNECTOR
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1552 nm
Nominal optical power output	1.122 mW
minimum return loss	-27 dB
Base Number Matches	1

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

AP500 and its application circuit (ab)

Non-two-wire sound and light control stair delay switch circuit (1)

Sensor equivalent circuit diagram

Fluorescent lamp stepless dimming electronic ballast circuit

One of the circuit diagrams to expand the output capacity of the power transformer

Making an infrared remote control DS1302 clock, encountered a problem: The infrared remote control uses external interrupt to receive and decode. In the main function, a while(1) is used to continuously read 1302. However, a problem is encountered now. Once an external i...; tianlai1009 51mcu

AD20 schematic diagram and PCB Cross select layout have problems: I use two monitors and draw in cross select mode. When I operate the PCB, such as selecting a device to rotate or deleting a trace, the PCB does not perform the corresponding operation, but the corres...; sparkshen PCB Design

i2c read problem - two results are different: Hello everyone, I have a chip connected to the i2c bus. I use the i2c read/write interface to write data to a certain area of the slave device, and then read it out to see if it has been written. But ...; 海洋dz Embedded System

What is the role of isolated power supply?: [size=4] In some isolation, it means electrical isolation between input and output, input and ground, and output and output. The purpose of isolation is to protect the safety of the system. When there...; qwqwqw2088 Analogue and Mixed Signal

Know the main technical indicators of some electrical instruments: 1. Error. No matter how good the quality of the instrument is, there is always an error between its measured value and the actual value. Therefore, "error" is the standard for measuring the accuracy o...; qwqwqw2088 Analogue and Mixed Signal

Encountered PCB antenna design problems: Is there anyone who is familiar with PCB antenna design? I want to use a PN532 chip to connect a 13.56Mhz antenna and integrate it with the PCB board, but I don’t know how to draw the antenna, and I d...; Ivanka PCB Design

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components