EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TLPLC388N

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-TLPLC388N Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,

PH1-TLPLC388N Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1554 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Looking for a single-chip minimum system schematic and PCB diagram
In order to complete my homework, I need to design a single-chip minimum system. I want to find a reference. Does anyone have one? If you can share it, I'd be very grateful!...
奔跑的蜗牛 51mcu
AD20 PCB copper plating PR, the copper plating is filled before it is closed. How to set it to not be filled before it is closed and displayed in dotted line form?
AD20 PCB copper plating PR, the copper plating is filled before it is closed. How to set it to not be filled before it is closed and displayed in dotted line form? Do not fill before closingAD20 is fi...
周旭权 PCB Design
Please explain this hardware circuit~~~~~
original:Since the wheelchair controller uses bipolar mode, there are four power tubes: T1 , T2 , T3 , T4 , among which the PWM pulse signals of T1 and T4 are the same, the PWM pulses of T2 and T3 are...
saikk DSP and ARM Processors
Using stm32f4 internal ram as cache displays normally, but using sdram displays fuzzy images!
[color=#000][backcolor=rgb(209, 217, 226)][font=Simsun]Using internal ROM as LTDC cache address display is normal: [/font][/backcolor][/color] [color=#000][backcolor=rgb(209, 217, 226)][font=Simsun]Us...
2459878559 stm32/stm8
Ask a question about message queues
I have been testing related projects these days, and there is a question that I don't understand: There are two tasks A and B in the vxworks environment, B has a higher priority. B receives messages a...
dandantcb Embedded System
LPC2132 driving ILI9320 TFT program problem
This is a program for TFT to display a red picture, but when running on the board, it takes almost an hour to display a complete picture. I don't know why. Please give me some advice.....................
Randy302 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 87  630  2016  2720  344  2  13  41  55  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号