Custom performance characteristics are available upon request. Use form C052 to detail
non-standard parameters.
Contact your local CTS Representative or CTS Customer Service for assistance.
* Prior to 11/7/06 the part number format did not contain this designator. These "Old Format" numbers (008-0261-0 Rev. E) are still valid with frequencies less than
or equal to 48.0000 MHz as Fundamental Mode designs. Frequencies above 48.0000 MHz will be Third Overtone designs. Refer to PCM-1211 for more details.
Document No. 008-0261-0
Page 1 - 3
Rev. F
٠ ٠ ٠
CTS Electronic Components, Inc.
٠
171 Covington Drive
٠
Bloomingdale, IL 60108
٠ ٠ ٠
٠ ٠ ٠
www.ctscorp.com
٠ ٠ ٠
7.0x5.0mm Low Cost
Surface Mount Crystal
Model 407
ELECTRICAL CHARACTERISTICS
PARAMETER
Operating Mode
(Note 1)
Crystal Cut
Frequency Range
Frequency Tolerance @ 25°C
Electrical Parameters
VALUE
Fundamental or 3
RD
Overtone
AT-Cut
8.0 MHz to 100.0 MHz
± 30 ppm Standard
(± 10 ppm and ± 20 ppm Available)
Frequency Stability Tolerance
(Operating Temperature Range, Referenced to 25°C Reading)
VS2008 uses Use MFC in a Static Library to generate ocx. It works well on WINCE, but it exits abnormally after changing to Use MFC in a Shared DLL. I guess the problem should be that a certain dll is ...
SIM300D can enable slow clock mode through AT+CSCLK=1, and then enter sleep mode, that is, slow clock mode, by pulling up the DTR pin. Now, without MUX started, the module can enter sleep mode, and th...
In addition, when running the program using evb programming, it shows that controls such as TreeView, Grid, etc. (non-ordinary controls) cannot be created. Thanks...
[b][url=http://www.deyisupport.com/question_answer/dsp_arm/c5000/f/48/t/141868.aspx]I would like to ask about the problem of writing the boot file of C5515 to the E2PROM of I2C[/url][/b][font=微软雅黑][si...
As medical equipment develops towards intelligence, miniaturization, serialization, digitization, and multi-functions, the logic control devices in medical equipment have also evolved from medium- a...[Details]
Ultrasonic tooth cleaning machines have been widely used in the medical field. Most ultrasonic tooth cleaning machines used at home and abroad now use analog oscillation circuits. There are the follow...[Details]
This article introduces a miniature home electrocardiograph. The instrument has powerful functions: display monitoring, storage, playback, printing, record management, power alarm, telephone or Intern...[Details]
Today, as network technology becomes more and more popular, industrial field instruments, data acquisition and control equipment are becoming more and more networked, and the combination of industr...[Details]
As the whole equipment is becoming increasingly miniaturized and power-saving, low-dropout linear regulators (LDOs) with low power consumption are becoming the mainstream in the market for linear regu...[Details]
To help improve DC/DC conversion efficiency at lighter loads and higher frequencies, Schottky diodes can be integrated into MOSFET chips to form a single package to reduce power dissipation in the ...[Details]
In order to meet the requirements of video systems, industrial and medical display and video transmission applications such as eliminating the limitation of long connection cables, increasing data ...[Details]
introduction
Controller Area Network (CAN) is a bus standard proposed by Bosch of Germany to solve the information communication between automotive electronic control units. With its exc...[Details]
introduction
Like other
portable
electronic products,
blood flow parameter detectors
need to be small, thin, durable, reliable, and have a long standby time. Therefore, system desi...[Details]
Preface
For a long time, SD cards with Flash Memory as storage have been widely used in consumer electronic products due to their small size, low power consumption, erasable and non-volati...[Details]
With the continuous emergence of new technologies and the increasing complexity of DSP real-time systems, there are more and more different types of external devices. Writing drivers for these exte...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data,...[Details]
1 Introduction
Economic development has prompted people to continuously improve their security awareness. When traditional local analog monitoring methods gradually fail to meet the needs of l...[Details]
Preface
In the application of PLL, DLL and CDR circuits, people generally require the output clock signal to have a 50% duty cycle so that data can be sampled at both the rising and fallin...[Details]
0 Introduction
In modern industrial production and scientific and technological research, various data usually need to be collected. The commonly used data acquisition board collection met...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
