Up to 400 mW Fiber Bragg Grating Stabilized 980 nm Pump Modules
2745 Series
Key Features
• High kink-free powers to 400 mW
• Reduced TEC power consumption, compatible with legacy
temperature control
• Low-profile 14-PIN butterfly planar package
• Fiber Bragg grating stabilization
• Wavelength selection available
• Integrated thermoelectric cooler, thermistor, and
monitor diode
• High dynamic range
Applications
• Dense wavelength division
multiplexing (DWDM) EDFAs for
small package designs
• High bit-rate, high channel-count EDFAs
• CATV distribution
The JDSU 2745 series of 980 nm pump modules uses a planar construction with
chip on subcarrier. The `semicooled' 45°C laser diode operation provides for a
significant reduction in TEC and overall power consumption. The high-power
JDSU laser chip is hermetically sealed in a low-profile, 14-pin butterfly package,
fitted with a thermistor, thermoelectric cooler, and monitor diode. The module
meets the stringent requirements of the telecommunications industry, including
Telcordia GR-468-CORE for hermetic 980 nm pump modules.
The 2745 series pump module, which uses fiber Bragg grating stabilization to lock
the emission wavelength, provides a noise-free, narrowband spectrum, even
under changes in temperature, drive current, and optical feedback. Wavelength
selection is available for applications requiring the highest performance in
spectrum control with the highest powers available.
Compliance
• Telcordia GR-468-CORE
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
2745 SERIES
2
Dimensions Diagram
250 µm Bare Fiber Type A Wiring
Note: Specifications in mm unless otherwise noted; tolerance = .x ± .3, .xx ± .20.
The module pigtail consists of 250 µm buffered, Corning PureMode
TM
HI-1060 Single-
mode fiber.
45.04
30.0
1600 M I N (1900 NOM )
1000 NOM . TO CENTER OF GRATING
26 . 0
20 . 8
17.8
1 .5
500 NOM . TO C/L OF SPLICE (OPTIONAL)
4 0 . 5 N O M . 1 5 . 5 1 2. 7
9 .0
STRAIN RELIEF
FLEXIBLE <=400
MICRON RECOAT
4.6
4X
2 .5 0 TH RU
1 2X 2 . 5 L E A D S P A C I N G
T O L E R A N C E I S N O N -A C C U M U L A T I V E
14X 0.51 LEAD WIDTH
260 < RECOAT <
935 (MICRON)
2.8
4.0 0
1.50
7 . 7 ±0. 20
RED NON-XYLENE MARK
FOR RECOAT WITH 295 35 μm
3. 9
1.5
5 . 6 T O L EA D C / L
2X ~ 5
5. 26
0.25 LEAD THICKNESS
Pinout
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
Cooler (+)
Thermistor
Monitor PD Anode
Monitor PD Cathode
Thermistor
N/C
N/C
N/C
N/C
Laser Anode
Laser Cathode
N/C
Case Ground
Cooler (-)
7
6
5
4
3
2
1
8
9
10
11
12
13
14
2745 SERIES
3
Table 1 Absolute Maximum Ratings
Parameter
Operating case temperature
Storage temperature
LD submount temperature
LD reverse voltage
LD forward current
LD current transient
LD reverse current
PD reverse voltage
PD forward current
Electrostatic discharge (ESD)
TEC current
TEC voltage
Axial pull force
Side pull force
Fiber bend radius
Relative humidity
Lead soldering time
Symbol
T
op
T
stg
T
LD
V
r
Test Conditions
-
2,000 hours
-
-
-
1 µs maximum
-
-
-
C = 100 pF, R = 1.5
Ω,
human body model
-
-
3 x 10 seconds
3 x 10 seconds
-
40°C
300°C
Minimum
-5°C
-40°C
0°C
-
-
-
-
-
-
-
-
-
-
-
16 mm
5%
-
Maximum
75°C
85°C
50°C
2V
1,000 mA
1,100 mA
10 µA
20 V
10 mA
1,000 V
2.5 A
4.0 V
5N
2.5 N
-
95%
10 seconds
V
PD
I
PD
V
ESD
I
TEC
V
TEC
R
H
Note: Absolute maximum ratings are the maximum stresses that may be applied to the pump module for short periods of time without causing damage. Stresses in excess of the absolute maximum ratings can
permanently damage the device. Exposure to absolute maximum ratings for extended periods, or exposure to more than one absolute maximum rating simultaneously may adversely affect device reliability.
Table 2 Operating Parameters
(BOL, T
case
= 0 to 75°C, T
LD
= 45°C, -50 dB reflection, unless noted otherwise)
Product Code
Maximum Operating
Power P
op
(mW)
100
120
135
155
170
190
205
225
240
260
275
295
310
330
340
Maximum Operating
Operating Current I
op
(mA)
300
320
330
360
400
440
480
520
560
600
640
680
725
780
820
Minimum Kink-Free
Power P
max
(mW)
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
Kink-Free Current
I
max
(mA) Maximum
340
355
380
420
460
510
560
600
650
700
750
820
860
910
950
27-xxxx-120-45
27-xxxx-140-45
27-xxxx-160-45
27-xxxx-180-45
27-xxxx-200-45
27-xxxx-220-45
27-xxxx-240-45
27-xxxx-260-45
27-xxxx-280-45
27-xxxx-300-45
27-xxxx-320-45
27-xxxx-340-45
27-xxxx-360-45
27-xxxx-380-45
27-xxxx-400-45
2745 SERIES
4
Table 3 Available Peak Wavelength Selection
(T
amb
= 25±3°C, 50 mW < P < P
op
)
Product Code
27-8000-xxx-45
27-7402-xxx-45
27-7552-xxx-45
27-7602-xxx-45
27-7702-xxx-45
Minimum Peak Wavelength
973.5 nm
973.5 nm
974.5 nm
975.0 nm
976.0 nm
Maximum Peak Wavelength
978.0 nm
975.0 nm
976.5 nm
977.0 nm
978.0 nm
Table 4 Electro-optical Performance
(BOL,T
case
= 0 to 75°C,T
LD
= 45°C, -50 dB reflection, unless noted otherwise)
Parameter
Threshold current
Forward voltage
Spectral width
Peak wavelength tuning
Side-mode suppression ratio
Relative optical power stability
Symbol
I
th
V
f
Δλ
RMS
Δλ
P
/ΔΤ
amb
SMSR
Test Condition
-
I
f
= I
op
50 mW < P < P
op
50 mW < P < P
op
50 mW < P < P
op
Peak-to-peak, T = 10 min,
50 kHz sampling, T
case
= 25 °C
20 mW < P < P
op
12 mW < P < 20 mW
3.5 mW < P < 12 mW
20 mW < P < P
op
1
20 mW < P < P
op
2
20 mW < P < P
op
T
case
= 75°C
T
case
= 75°C
-
-
Minimum
-
-
-
-
15 dB
Maximum
40 mA
2.5 V
2.0 nm
0.02 nm/°C
-
Tracking error
Tracking ratio
Monitor diode responsivity
TEC current
TEC voltage
Thermistor resistance
Thermistor constant
TE
TR
Resp
BF
I
TEC
V
TEC
R
th
B
-
-
-
-25%
0.75
2 µA/mW
-
-
9.5 kΩ
3600 K
4%
10%
25%
25%
1.25
10 µA/mW
1.5 A
2.5 V
10.5 kΩ
4200 K
1. The Tracking Error is defined as the normalized change of output power relative to the operating power over case temperature range 0°C to 75°C, at constant back face monitor current corresponding
to the operating power at 25°C.
2. The Tracking Ratio is a measure of the front-to-back tracking when the output power is varied. On a plot of optical power versus back-face photocurrent, a straight line is drawn between the minimum
power (20 mW) and the operating power P
op
points. The tracking ratio is defined as the ratio between measured optical power (shown as data points on the plot) to the value derived from the straight line.
2745 SERIES
5
Table 5 TEC and Total Module Power Consumption
(For
ΔT
= 30°C, BOL, T
case
= 75°C, T
ld
= 45°C unless noted otherwise)
Product Code
TEC Current
I
max
(A)
0.58
0.60
0.63
0.65
0.69
0.71
0.78
0.83
0.90
0.94
1.00
1.06
1.13
1.21
1.28
TEC Voltage
V
max
(V)
0.90
0.92
0.96
0.98
1.04
1.07
1.17
1.25
1.31
1.38
1.45
1.52
1.57
1.65
1.75
TEC Power Consumption
P
max
(W)
0.52
0.55
0.60
0.64
0.72
0.76
0.91
1.04
1.18
1.30
1.45
1.61
1.77
2.00
2.24
Total Module Power
Consumption P
max
(W)
1.01
1.08
1.17
1.26
1.43
1.56
1.81
2.04
2.28
2.51
2.76
3.03
3.31
3.68
4.03
27-xxxx-120-45
27-xxxx-140-45
27-xxxx-160-45
27-xxxx-180-45
27-xxxx-200-45
27-xxxx-220-45
27-xxxx-240-45
27-xxxx-260-45
27-xxxx-280-45
27-xxxx-300-45
27-xxxx-320-45
27-xxxx-340-45
27-xxxx-360-45
27-xxxx-380-45
27-xxxx-400-45
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at
【Chuanglong TL570x-EVM】Review 0 8 - QT Network Communication-TCP-UDP
1. QT software source
The software code used for this function verification comes from the book "QT5.9C++ Development Guide", which...
Share a simulation model that uses AT89C51 to generate PWM signals to control the speed of a DC motor. Software environment: Keil C51, Proteus Existing files: Keil C51 project files, C51 source files,...
[i=s]This post was last edited by wangerxian on 2022-2-16 09:30[/i]Hello everyonePower supply technology - I believe that many friends in the forum have some obsession with this . When applying embedd...
Which websites and forums do you go to learn Labview? I often go to two websites. [url=http://www.ni.com]www.ni.com[/url] is the NI website. How can I not go there to learn Labview? The second is [url...
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
