Up to 400 mW Fiber Bragg Grating Stabilized 980 nm Pump Modules
2745 Series
Key Features
• High kink-free powers to 400 mW
• Reduced TEC power consumption, compatible with legacy
temperature control
• Low-profile 14-PIN butterfly planar package
• Fiber Bragg grating stabilization
• Wavelength selection available
• Integrated thermoelectric cooler, thermistor, and
monitor diode
• High dynamic range
Applications
• Dense wavelength division
multiplexing (DWDM) EDFAs for
small package designs
• High bit-rate, high channel-count EDFAs
• CATV distribution
The JDSU 2745 series of 980 nm pump modules uses a planar construction with
chip on subcarrier. The `semicooled' 45°C laser diode operation provides for a
significant reduction in TEC and overall power consumption. The high-power
JDSU laser chip is hermetically sealed in a low-profile, 14-pin butterfly package,
fitted with a thermistor, thermoelectric cooler, and monitor diode. The module
meets the stringent requirements of the telecommunications industry, including
Telcordia GR-468-CORE for hermetic 980 nm pump modules.
The 2745 series pump module, which uses fiber Bragg grating stabilization to lock
the emission wavelength, provides a noise-free, narrowband spectrum, even
under changes in temperature, drive current, and optical feedback. Wavelength
selection is available for applications requiring the highest performance in
spectrum control with the highest powers available.
Compliance
• Telcordia GR-468-CORE
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
2745 SERIES
2
Dimensions Diagram
250 µm Bare Fiber Type A Wiring
Note: Specifications in mm unless otherwise noted; tolerance = .x ± .3, .xx ± .20.
The module pigtail consists of 250 µm buffered, Corning PureMode
TM
HI-1060 Single-
mode fiber.
45.04
30.0
1600 M I N (1900 NOM )
1000 NOM . TO CENTER OF GRATING
26 . 0
20 . 8
17.8
1 .5
500 NOM . TO C/L OF SPLICE (OPTIONAL)
4 0 . 5 N O M . 1 5 . 5 1 2. 7
9 .0
STRAIN RELIEF
FLEXIBLE <=400
MICRON RECOAT
4.6
4X
2 .5 0 TH RU
1 2X 2 . 5 L E A D S P A C I N G
T O L E R A N C E I S N O N -A C C U M U L A T I V E
14X 0.51 LEAD WIDTH
260 < RECOAT <
935 (MICRON)
2.8
4.0 0
1.50
7 . 7 ±0. 20
RED NON-XYLENE MARK
FOR RECOAT WITH 295 35 μm
3. 9
1.5
5 . 6 T O L EA D C / L
2X ~ 5
5. 26
0.25 LEAD THICKNESS
Pinout
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
Cooler (+)
Thermistor
Monitor PD Anode
Monitor PD Cathode
Thermistor
N/C
N/C
N/C
N/C
Laser Anode
Laser Cathode
N/C
Case Ground
Cooler (-)
7
6
5
4
3
2
1
8
9
10
11
12
13
14
2745 SERIES
3
Table 1 Absolute Maximum Ratings
Parameter
Operating case temperature
Storage temperature
LD submount temperature
LD reverse voltage
LD forward current
LD current transient
LD reverse current
PD reverse voltage
PD forward current
Electrostatic discharge (ESD)
TEC current
TEC voltage
Axial pull force
Side pull force
Fiber bend radius
Relative humidity
Lead soldering time
Symbol
T
op
T
stg
T
LD
V
r
Test Conditions
-
2,000 hours
-
-
-
1 µs maximum
-
-
-
C = 100 pF, R = 1.5
Ω,
human body model
-
-
3 x 10 seconds
3 x 10 seconds
-
40°C
300°C
Minimum
-5°C
-40°C
0°C
-
-
-
-
-
-
-
-
-
-
-
16 mm
5%
-
Maximum
75°C
85°C
50°C
2V
1,000 mA
1,100 mA
10 µA
20 V
10 mA
1,000 V
2.5 A
4.0 V
5N
2.5 N
-
95%
10 seconds
V
PD
I
PD
V
ESD
I
TEC
V
TEC
R
H
Note: Absolute maximum ratings are the maximum stresses that may be applied to the pump module for short periods of time without causing damage. Stresses in excess of the absolute maximum ratings can
permanently damage the device. Exposure to absolute maximum ratings for extended periods, or exposure to more than one absolute maximum rating simultaneously may adversely affect device reliability.
Table 2 Operating Parameters
(BOL, T
case
= 0 to 75°C, T
LD
= 45°C, -50 dB reflection, unless noted otherwise)
Product Code
Maximum Operating
Power P
op
(mW)
100
120
135
155
170
190
205
225
240
260
275
295
310
330
340
Maximum Operating
Operating Current I
op
(mA)
300
320
330
360
400
440
480
520
560
600
640
680
725
780
820
Minimum Kink-Free
Power P
max
(mW)
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
Kink-Free Current
I
max
(mA) Maximum
340
355
380
420
460
510
560
600
650
700
750
820
860
910
950
27-xxxx-120-45
27-xxxx-140-45
27-xxxx-160-45
27-xxxx-180-45
27-xxxx-200-45
27-xxxx-220-45
27-xxxx-240-45
27-xxxx-260-45
27-xxxx-280-45
27-xxxx-300-45
27-xxxx-320-45
27-xxxx-340-45
27-xxxx-360-45
27-xxxx-380-45
27-xxxx-400-45
2745 SERIES
4
Table 3 Available Peak Wavelength Selection
(T
amb
= 25±3°C, 50 mW < P < P
op
)
Product Code
27-8000-xxx-45
27-7402-xxx-45
27-7552-xxx-45
27-7602-xxx-45
27-7702-xxx-45
Minimum Peak Wavelength
973.5 nm
973.5 nm
974.5 nm
975.0 nm
976.0 nm
Maximum Peak Wavelength
978.0 nm
975.0 nm
976.5 nm
977.0 nm
978.0 nm
Table 4 Electro-optical Performance
(BOL,T
case
= 0 to 75°C,T
LD
= 45°C, -50 dB reflection, unless noted otherwise)
Parameter
Threshold current
Forward voltage
Spectral width
Peak wavelength tuning
Side-mode suppression ratio
Relative optical power stability
Symbol
I
th
V
f
Δλ
RMS
Δλ
P
/ΔΤ
amb
SMSR
Test Condition
-
I
f
= I
op
50 mW < P < P
op
50 mW < P < P
op
50 mW < P < P
op
Peak-to-peak, T = 10 min,
50 kHz sampling, T
case
= 25 °C
20 mW < P < P
op
12 mW < P < 20 mW
3.5 mW < P < 12 mW
20 mW < P < P
op
1
20 mW < P < P
op
2
20 mW < P < P
op
T
case
= 75°C
T
case
= 75°C
-
-
Minimum
-
-
-
-
15 dB
Maximum
40 mA
2.5 V
2.0 nm
0.02 nm/°C
-
Tracking error
Tracking ratio
Monitor diode responsivity
TEC current
TEC voltage
Thermistor resistance
Thermistor constant
TE
TR
Resp
BF
I
TEC
V
TEC
R
th
B
-
-
-
-25%
0.75
2 µA/mW
-
-
9.5 kΩ
3600 K
4%
10%
25%
25%
1.25
10 µA/mW
1.5 A
2.5 V
10.5 kΩ
4200 K
1. The Tracking Error is defined as the normalized change of output power relative to the operating power over case temperature range 0°C to 75°C, at constant back face monitor current corresponding
to the operating power at 25°C.
2. The Tracking Ratio is a measure of the front-to-back tracking when the output power is varied. On a plot of optical power versus back-face photocurrent, a straight line is drawn between the minimum
power (20 mW) and the operating power P
op
points. The tracking ratio is defined as the ratio between measured optical power (shown as data points on the plot) to the value derived from the straight line.
2745 SERIES
5
Table 5 TEC and Total Module Power Consumption
(For
ΔT
= 30°C, BOL, T
case
= 75°C, T
ld
= 45°C unless noted otherwise)
Product Code
TEC Current
I
max
(A)
0.58
0.60
0.63
0.65
0.69
0.71
0.78
0.83
0.90
0.94
1.00
1.06
1.13
1.21
1.28
TEC Voltage
V
max
(V)
0.90
0.92
0.96
0.98
1.04
1.07
1.17
1.25
1.31
1.38
1.45
1.52
1.57
1.65
1.75
TEC Power Consumption
P
max
(W)
0.52
0.55
0.60
0.64
0.72
0.76
0.91
1.04
1.18
1.30
1.45
1.61
1.77
2.00
2.24
Total Module Power
Consumption P
max
(W)
1.01
1.08
1.17
1.26
1.43
1.56
1.81
2.04
2.28
2.51
2.76
3.03
3.31
3.68
4.03
27-xxxx-120-45
27-xxxx-140-45
27-xxxx-160-45
27-xxxx-180-45
27-xxxx-200-45
27-xxxx-220-45
27-xxxx-240-45
27-xxxx-260-45
27-xxxx-280-45
27-xxxx-300-45
27-xxxx-320-45
27-xxxx-340-45
27-xxxx-360-45
27-xxxx-380-45
27-xxxx-400-45
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at
Shanghai Boda Data Communication Co., Ltd. is recruiting FPGA design engineers and power development engineers. If you are interested, please send your resume to: yangrong@bdcom.com.cn , or leave your...
[code]Windows Embedded Standard SP2 genuine full set 9CD version
I won't go into detail about the software's features and introduction. You can check it out on Microsoft's official website ( http://ww...
I set a breakpoint at this step, and the IP array I drew is a string of numbers.I click next statement now, and run to the green area, and find that the IP has not changed.I re-run the program and run...
Dear prawns :I have the following two requirements , hope that capable experts can give me some advice :1. There is water in a larger container, and then a smaller glass container is placed inside. Th...
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
Almost everyone in a student dormitory has a bedside lamp. But if you want to read for a while after turning off the lights and don't want to disturb your roommates' sleep, you may need a reading l...[Details]
The fluorescent lamps and energy-saving lamps we commonly use now have greatly improved luminous efficiency compared with the earlier ordinary incandescent lamps and have been widely used. With the...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems (GP...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
