D at a
S hee t
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or V
IO
range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
2
S71WS-P based MCP Products
S71WS-P_00_A16 November 11, 2010
S71WS-P based MCP Products
1.8 Volt-only x16 Simultaneous Read/Write, Burst Mode
Flash Memory with CellularRAM
Data Sheet
Features
Power supply voltage of 1.7 to 1.95V
Flash access time: 80 ns, 20 ns
Flash burst frequencies: 66 MHz, 80 MHz, 104 MHz
pSRAM Access time: 70 ns, 20 ns
pSRAM burst frequency: 66 MHz, 80 MHz, 104 MHz
Package:
– 8.0 x 11.6 mm MCP
Operating Temperature
– –25°C to +85°C (wireless)
The S71WS series is a product line of stacked packages and consists of:
One S29WS-P NOR flash memory die
CellularRAM die
The products covered by this document are listed in the table below.
CellularRAM Density (Mb)
Device
S29WS512P
S29WS256P
S29WS128P
S71WS128PB0
S71WS256PC0
32 Mb
64 Mb
128 Mb
S71WS512PD0
Note:
For a full list of OPNs, please contact the local sales representative or refer to the Ordering Information valid combinations tables.
For detailed specifications, please refer to the individual data sheets.
Document
S29WS-P
128M CellularRAM Type 5
64M CellularRAM PN: SWM064D133S1R
32M CellularRAM PN: SWM032D133S1R
Publication Identification Number (PID)
S29WS-P_00
CustComspec_00
SWM064D133S1R
SWM032D133S1R
Publication Number
S71WS-P_00
Revision
A
Amendment
16
Issue Date
November 11, 2010
Data
She et
3. Connection Diagrams
1
A
DNU
B
AVD#
C
F-WP#
D
A3
E
A2
F
A1
G
A0
H
F-CE#
J
R-CE#
K
RFU
L
RFU
M
DNU
DNU
RFU
VSS
F-VCC
RFU
RFU
F-VCCQ
DNU
DQ8
DQ2
DQ11
RFU
DQ5
DQ14
RFU
DQ0
DQ10
F-VCC
R-VCC
DQ12
DQ7
VSS
OE#
DQ9
DQ3
DQ4
DQ13
DQ15
R-CRE
Do Not Use
VSS
DQ1
RFU
RFU
DQ6
A24
A16
A4
A17
RFU
A23
A10
A14
A22
Flash & pSRAM
Shared Only
A5
A18
RDY
A20
A9
A13
A21
pSRAM Only
A6
R-UB#
F-RST#
RFU
A19
A12
A15
NOR Flash Only
A7
R-LB#
F-ACC
WE#
A8
A11
RFU
Reserved for
Future Use
VSS
CLK
RFU
F-VCC
RFU
RFU
RFU
Legend
DNU
2
3
4
5
6
7
8
9
10
Note:
1. V
CC
pins must ramp simultaneously.
MCP
S71WS512PD0
S71WS256PC0
S71WS128PB0
Flash-only Addresses
A24-A23
A23-A22
A22-A21
Shared Addresses
A22-A0
A21-A0
A20-A0
3.1
Special Handling Instructions For FBGA Package
Special handling is required for Flash Memory products in FBGA packages.
Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The
package and/or data integrity may be compromised if the package body is exposed to temperatures above
150°C for prolonged periods of time.
3.2
Look-ahead Ballout for Future Designs
Please refer to the Design-in Scalable Wireless Solutions with Spansion Products application note
(publication number: Design_Scalable_Wireless). Contact your local Spansion sales representative for more
details.
November 11, 2010 S71WS-P_00_A16
S71WS-P based MCP Products
5
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
