LPW049-1270-07CB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> LPW049-1270-07CB95

LPW049-1270-07CB95: DescriptionIC Socket, BGA49, 49 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

LPW049-1270-07CB95 Overview

IC Socket, BGA49, 49 Contact(s), ROHS COMPLIANT

LPW049-1270-07CB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA49
Shell material	PLASTIC
JESD-609 code	e4/e3
Manufacturer's serial number	LPW
Number of contacts	49
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Ultrasonic fault tracking circuit

LED lighting display detection circuit with overload protection

High performance automatic balancing charger circuit

Silicon photodiode amplifier circuit

High precision fast sample and hold circuit circuit diagram

Adjustable voltage stabilized power supply circuit diagram using op amp

[SAM R21] Found a new issue with USB CDC: [i=s]This post was last edited by dcexpert on 2015-1-28 11:38[/i] A new problem has been found on SAM R21. After adding delay routines, the virtual serial port will not work and no data can be receive...; dcexpert Microchip MCU

Weird LoadImage() failure: I am using WinCE5.0, and I add my own images to explorebase.rc for HPC. a. If the image is generated by sysgen or build sysgen, when I execute LoadImage, it fails and GetLastError() returns 1814. b. I...; hailangties Embedded System

Focus on the latest competition between the two CPU giants and analyze the trend of multi-core processors: A fierce battle over computer processors is quietly escalating as AMD and Intel compete to define interconnect rules for their next-generation multi-core processors . Both companies hope to weave a se...; xuebin RF/Wirelessly

Talk about love: Tonight I saw my roommate watching a TV series, so I watched two episodes with him. The TV series is called "Talk About Love", and the two episodes I watched were very touching. Love is really a wonde...; fengxin Talking

Problems with the Linux development board: I want to learn Linux and buy a development board. I bought a board from Wei Dongshan a few years ago. I studied for a while but gave up. Isold the board. Now I want to learn again. I saw Huaqing Yuan...; chenbingjy Linux and Android

A small software for commonly used development tools written by myself: A small software I wrote for common development tools...; 奋斗吧小鱼儿 51mcu

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components